Heatrae Sadia Multipoint 10 and 15 litre Fitting Instructions Manual Download Page 14

14

12.  Spare parts

The following comprehensive list of spare parts is 

available for your product. Please refer to the Rating 

Label on the side of your product before ordering to 

ensure the correct spare part is obtained. 

Do not replace with parts not recommended by 

Heatrae Sadia - this will invalidate your warranty and 

may render the installation dangerous.

11.  Decommissioning procedure

 

`

Isolate electrical supplies and make safe

 

`

Isolate the water supply

 

`

Drain the product

 

`

Remove product

 

`

Cap pipework

Environmental information

The Waste Electrical and Electronic Equipment 

(Producer Responsibility) Regulation 2004

This product is outside of the scope of the European 

Waste Electrical & Electronic Equipment Directive as 

interpreted within the UK.

In the UK this product can therefore be disposed of 

through commercial non-WEEE waste facilities.

Heatrae Sadia does not accept any liability under the 

WEEE directive.

This product is manufactured from many recyclable 

materials. At the end of its useful life it should be 

disposed of at a Local Authority Recycling Centre to 

realise the full environmental benefits. 

Insulation of the product is by means of an approved 

CFC/HCFC free polyurethane foam with an ozone 

depletion factor of zero and a Global Warming 

Potential (GWP) of 3.1.

The product does not contain any substances 

harmful to health; it does not contain any asbestos.

Description

Code No

Element plate assembly -  

10 litre 3kW

95 606 921

Element plate assembly -  

15 litre 3kW

95 606 922

Element plate assembly -  

10 litre 4.5kW

95 606 923

Element plate assembly -  

15 litre 4.5kW

95 606 924

Combined thermostat/thermal  

cut-out 3kW

95 612 633

Combined thermostat/thermal  

cut-out 4.5kW

95 612 634

Indicator light 3kW

95 607 992

Indicator light 4.5kW

95 607 993

Element plate gasket

95 611 708

Pressure (expansion) Relief Valve

95 607 986

Temperature/Pressure Relief Valve

95 605 045

Check Valve

95 607 987

Expansion Vessel

95 607 988

Pressure Reducing Valve

95 607 989

Top cover moulding

95 614 181

Terminal cover c/w thermostat knob

95 614 182

Summary of Contents for Multipoint 10 and 15 litre

















Reviews: