background image

9

Hearth & Home Technologies  •  IFT-RC400U User Manual  •  2564-983  •  10/20

Please contact your Hearth & Home Technologies 

dealer with any questions or concerns. 

For the location of your nearest 

Hearth & Home Technologies dealer, 

please visit www.hearthnhome.com.

Regulatory Certification

 

The IFT-RC400 wireless wall switch is certified for op

-

eration in the following countries: 
•  United States 

•  Canada  

•  Australia/New Zealand

  

United States

   The IFT-RC400 complies with all applicable FCC  

   equipment authorization, regulations, requirements,  

   and equipment functions.

This equipment has been tested and found to comply 

with the limits for a Class B digital device, pursuant to 

Part 15 of the FCC Rules. These limits are designed 

to provide reasonable protection against harmful in-

terference in a residential installation. This equipment 

generates uses and can radiate radio frequency energy 

and, if not installed and used in accordance with the 

instructions, may cause harmful interference to radio 

communications. However, there is no guarantee that 

interference will not occur in a particular installation. If 

this equipment does cause harmful interference to ra-

dio or television reception, which can be determined by 

turning the equipment off and on, the user is encour

-

aged to try to correct the interference by one or more of 

the following measures:
    •  Reorient or relocate the receiving antenna. 

 

    •  Increase the separation between the equipment  

       and receiver.   

 

    •  Connect the equipment into an outlet on a circuit  

       different from that to which the receiver is con-

 

       nected.  

 

   •  Consult the dealer or an experienced radio/TV  

       techcian for help 

Changes or modifications not expressly approved by 

the party responsible for compliance could void the 

user’s authority to operate the equipment.

Canada

The IFT-RC400 is certified for use in Canada under

 

Industry Canada (IC) Radio Standards Specification 

(RSS

).

This device complies with Industry Canada license 

exempt RSS standard(s). Operation is subject to the 

following two conditions: (1) this device may not cause 

interference, and (2) this device must accept any inter-

ference, including interference that may cause unde-

sired operation of the device.

  

Le présent appareil est conforme aux CNR d’Industrie 

Canada applicables aux appareils radio exempts de 

licence. L’exploitation est autorisée aux deux onditions 

suivantes: (1) l’appareil ne doit pas produire de brouil-

lage, et (2) l’utilisateur de l’appareil doit accepter tout 

brouillage radioélectrique subi, meme si le brouillage 

est susceptible d’en compromettre le fonctionnement. 

The IFT-RC400 is labelled with a unique FCC ID num-

ber. The following label is placed on the back cover of 

the wireless wall switch control housing: 

FCC ID: ULE2564-110

This device complies with Part 15 of the FCC Rules. 

Operation is subject to the following two conditions: 

(1) This device may not cause harmful interference 

and,

(2) This device must accept any interference received, 

including interference that may cause undesired op-

eration. 

The IFT-RC400 label displays the Industry Canada certi-

fication number as follows: 

IC: 6732A-2564110

Australia/New Zealand

Australian/New Zealand radio regulations do not 

provide a policy similar to the United States (FCC) 

or Canada (IC). However, IFT-RC400 test reports 

maybe used in part to demonstrate compliance in 

accordance with ACMA Radio communications “Short 

Range Devices” Standard which references Australia/

New Zealand industry standard AS/NZS4268:2014. 

The IFT-RC400 test reports may be used as part of the 

product certification and compliance folder.

Summary of Contents for 2564-110










Reviews: