background image

TriStar Variable Speed Pump Control   ____                      ____________________________Page 2 of 16 

WWW.HAYWARDPOOL.COM              USE ONLY HAYWARD GENUINE REPLACEMENT PARTS 

IMPORTANT SAFETY INSTRUCTIONS

 

Before installing or servicing this electrical equipment, turn power supply OFF.

 

WARNING

– Read and follow all instructions in this 

owner’s manual and on the equipment.  Failure to follow 
instructions can cause severe injury and/or death. 

WARNING –

This product should be installed and serviced only by a qualified professional.

 

CAUTION –

All electrical wiring MUST be in conformance with all applicable local codes, regulations, and the 

National Electric Code (NEC).

 

Use of non­Hayward replacement parts voids warranty. 

ATTENTION INSTALLER – THIS MANUAL CONTAINS IMPORTANT INFORMATION ABOUT THE INSTALLATION, 
OPERATION, AND SAFE USE OF THIS PUMP THAT MUST BE FURNISHED TO THE END USER OF THIS PRODUCT. 
FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS COULD RESULT IN SERIOUS INJURY. 

WARNING 

 

To reduce risk of injury, do not permit children to use or climb on this product.  Closely supervise children 

at all times.  Components such as the filtration system, pumps, and heaters must be positioned to prevent children from using them as a 
means of access to the pool.

 

CAUTION 

 

This pump is intended for use on permanently installed swimming pools and may also be used with hot tubs 

and spas if so marked.  Do NOT use with storable pools.  A permanently installed pool is constructed in or on the ground or in a 
building such that it cannot be readily disassembled for storage.  A storable pool is constructed so that it is capable of being readily 
disassembled for storage and reassembled to its original integrity.  Though this product is designed for outdoor use, it is strongly 
advised to protect the electrical components from the weather.  Select a well­drained area, one that will not flood when it rains.  It 
requires free circulation of air for cooling.  Do not install in a damp or non­ventilated location.  If installed within an outer enclosure 
or beneath the skirt of a hot tub or spa, adequate ventilation and free circulation of air must be provided to prevent overheating of the 
motor.

WARNING 

 

Pool and spa components have a finite life.  All components should be inspected frequently and replaced at 

least every ten years, or if found to be damaged, broken, cracked, missing, or not securely attached. 

Basic safety precautions should always be followed, including the following: Failure to follow instructions may result in injury. 

This is the safety­alert symbol. When you see this symbol on your pump or in this manual, look for one of the following 

signal words and be alert to the potential for personal injury.

 

WARNING

 

warns about hazards that

could

 cause serious personal injury, death or major property damage and if 

ignored presents a potential hazard.

 

CAUTION

 

warns about hazards that

will

 or

 can

 cause minor or moderate personal injury and/or property damage 

and if ignored presents a potential hazard.  It can also make consumers aware of actions that are unpredictable and unsafe. 

The

NOTICE

 label indicates special instructions that are important but not related to hazards.

Summary of Contents for TriStar SP322063EEV

















Reviews: