157
4001055250
E 10.21
USA / GB
Chassis and turret
Dismantling / Reassembling wheels reducer
MS0026
1.
Perform Roll Check, Leak Chake and Brake Check if applicable prior to disassembling the unit.
2.
Drain oil from unit. Note the condition and volume of the oil.
3.
Remove retaining Ring ( 6G ) by prying the open end of Retaining Ring out of the groove in the Ring
Gear ( 1E ) with a screwdriver, then grasp the loose end with pliers and pull the Retaining Ring com-
pletely out of the groove.
4.
Remove the Cover ( 6 ) from the unit. The unit can be carefully pressurized with air to pop the cover
out of the unit.
5.
Remove the First Stage Sun Gear ( 10 ) if applicable.
N.B.-:-O
N
UNITS
WITH
RATIOS
GREATER
TTHAN
36:1
NUMERICALLY
,
THERE
WILL
NOT
BE
A
SEPARATE
F
IRST
S
TAGE
S
UN
G
EAR
( 10 ),
AS
THE
GEAR
TEETH
WILL
BE
INTEGRAL
TO
THE
I
NPUT
S
HAFT
( 9 ).
6.
Remove the Input Carrier ( 3 ).
7.
Remove the Second Stage Sun Gear ( 11 ).
8.
Take the External retaining Ring ( 20 ) off the Sun Gear ( 11 ) if necessary.
9.
Loosen and remove the 3 Flat Heat Bolts ( 19 ) that retain the Ring Gear ( 1E ) to the Housing ( 1G ).
10.
Lift the Ring Gear ( 1E ) off the Housing ( 1D ).
11.
Remove the O-ring ( 18 ) from between the Housing ( 1D ) and the Ring Gear ( 1E ).
Summary of Contents for HT23RTJ O
