Harsco Industrial MACH C1500GG Installation & Owner'S Manual Download Page 61 | Manualshive

Page: 61 / 61

Harsco Industrial MACH C1500GG Installation & Owner'S Manual Download Page 61

MACH® Gas-Fired Boiler

61

Before commissioning, a sample of the system water and the make-up water should be analyzed to assure the
proper mixture of water, chemical treatment and (if applicable) glycol.  This analysis can be made by your local
water treatment firm, or by one of the manufacturers listed below.  The water chemistry should be adjusted as
recommended in the analysis results.  Thereafter, the system water should be analyzed at the start of the
heating season for boilers operated for comfort heat only or twice annually for boilers that are operated year
round.

There are many suppliers of chemical treatments that are acceptable for use in multi-metal hydronic systems.
The Association of Water Technologies maintains a listing of manufacturers and water treatment firms and
professionals for reference. This listing can be found on the internet at

, click on the “Find a Water

Treater” button.

The following companies have certified their water treatment systems as safe for use with multi-metal hydronic
systems that include aluminum boilers. These manufacturers provide treatments to chemical service
companies, through either direct sales or wholesalers. Further information is available by contacting one of the
individuals listed below:

Fernox

Hydronic Agencies Ltd.
Edmonton, AB, CANADA
Phone: (780) 452-8661
Toll Free: (877) FERNOX4U

(877-337-6694)

Fax: (780) 488-2304
Email:

[email protected]

www.hydronicagencies.com

Fernox USA

Cookson Electronics
Altoona PA
Phone: (814) 946-1611
Toll Free (800) 289-3797
Fax: (814) 944-8094
Email:

[email protected]

H-O-H Water Technology, Inc.

Greendale, WI
Phone: (414) 421-2070,

Rhomar Water Management, Inc.

Springfield, MO
Phone: (417) 862-2600,
Toll Free: (800) 543-5975
Fax: (417) 862-6410
Email: [email protected]

www.rhomarwater.com

Sentinel Performance Solutions Ltd.

Marathon Distributors
Mississauga ON Canada
Toll Free: (888) 602-5360

www.sentinel-solutions.net/en/

Sentinel Performance Solutions Ltd.

Douglas Products and Packaging
Liberty, MO
Toll Free: (877) 567-2560
Email:

[email protected]

www.douglasproducts.com

Toll Free: (800) 944-9746
Fax: (414) 421-2077
Email:

[email protected]

www.hohwatertechnology.com

«
...
59
60
61

Summary of Contents for MACH C1500GG






























































Reviews:

No comments