Harsco Industrial MACH C1500GG Installation & Owner'S Manual Download Page 46

Page: 46 / 61

MACH® Gas-Fired Boiler

Page 46

5.5.11 Auto-reset Error Codes

– E##

Code ENVI

™ Control Display

Lockout

Description

E01

OUT TEMP SENS OPEN

Outlet Temperature Sensor Open

Boiler outlet water temperature sensor open circuit

E02

IN TEMP SENS OPEN

Inlet Temperature Sensor Open

Boiler inlet water sensor temperature open circuit

E03

FLUE TMP SENS OPEN

Flue Temperature Sensor Open

Boiler flue gas temperature sensor open circuit

E04

DHW TEMP SENS OPEN DHW Temperature Sensor Open

Domestic Hot Water temperature sensor open circuit

E05

HX TEMP SENS OPEN

Heat Exchanger Temperature Sensor
Open

Heat Exchange temperature sensor open circuit

E11

OUT TEMP SENS
SHORT

Outlet Temperature Sensor Short

Boiler outlet water temperature sensor short circuit

E12

IN TEMP SENS SHORT

Inlet Temperature Sensor Short

Boiler inlet water temperature sensor short circuit

E13

FLUE TMP SENS SHORT Flue Temperature Sensor Short

Boiler flue gas temperature sensor short circuit

E14

DHW TEMP SENS
SHORT

DHW Temperature Sensor Short

Domestic Hot Water temperature sensor short circuit

E15

HX TEMP SENS SHORT

Heat Exchanger Temperature Sensor
Short

Heat Exchange temperature sensor short circuit

E16

HEADER SENS SHORT

Header Temperature Sensor is
defective

Header temperature sensor on IF board has a short
circuit or an open circuit

E18

LINE NEUTRAL REV

Electrical Error

Hot and Neutral are reversed

E20

FALSE FLAME

False Flame

Flame detected when no flame should be present

E21

LOW FLOW / ILK

Low Water Flow or Open Interlock
Circuit

E21 converts to A07 after 5 minutes

E22

NO GROUND 60 HZ ERR No Ground error

No ground connected or voltage on ground

E23

LINE FREQUENCY ERR

Line Frequency Error

Line frequency deviates from 60Hz by more than 2%

E24

FAULTY GROUND

Faulty Ground

Ground/Earth connection is not functioning correctly

E30

HIGH FLUE TEMP

Flue Gas Temperature Too High

Temperature of the flue gas is greater than setpoint
+ differential

E32

HIGH INLET TEMP

Inlet Temp Too High

Inlet water is greater than 194°F

E34

BLOCKED FLUE

Blocked Flue

Hi exhaust back pressure switch is tripped due to
excess pressure in the flue/stack or excessive
negative cabinet pressure

E41

REVERSE FLOW IN OUT Reversed Water Flow

The water flow through the boiler is reversed (Inlet
water is hotter than outlet water)

E42

INTERAL ERROR 48

Internal Error 48

Call for service.

E46

INTERAL ERROR 35

Internal Error 35

Call for service.

E47

INTERAL ERROR 36

Internal Error 36

Call for service.

E48

INTERAL ERROR 37

Internal Error 37

Call for service.

E49

RAPID RISE HX ERROR

Rapid Rise Heat Exchanger
Temperature

Temperature across heat exchanger is rising faster
than allowed

E50

RAPID RISE ERROR

Rapid Rise Outlet Temp

Temperature of the Outlet water is rising faster than
allowed

E51

INTERNAL ERROR 67

Internal Error 67

Call for Service

E52

WRONG BOILER TYPE

Wrong Boiler Type

Control and Boiler do not match (control is
programmed for another type of Harsco boiler)

E 54

IF COMM FAILURE

Interface Board Failure

No communication with Interface Board

Summary of Contents for MACH C1500GG






























































Search results

Summary of Contents for MACH C1500GG

Reviews:

Harsco Industrial MACH C1500GG, Installation & Owner'S Manual, Page: 46 / 61

Search results

Summary of Contents for MACH C1500GG

Reviews: