manualshive.com logo in svg

Harsco Industrial MACH C1500GG, Installation & Owner'S Manual, Page: 10 / 61

Share
Download
Harsco Industrial MACH C1500GG Installation & Owner'S Manual Download Page 10

 

 

 

 
 
 

 

MACH® Gas-Fired Boiler 

 

 

Page  10 

 

 

†  "C"  Space required for pipes, ducts, etc. in this area above 
the boiler.  

* Clearance depends upon exhaust vent configuration. 

**  Service access is required on left side of boiler to facilitate 
boiler maintenance

.  Minimum 2” clearance is required on 

right side

.  

Do not put pipes, ducts, vents, etc in this space.  

Electrical conduit must be installed vertically so that the side 
doors can be opened. 

 

  Bumping hazard from overhead ducts!  Install all components with adequate 

vertical clearances.  

 
 

3.4 

E

LECTRICAL 

C

ONNECTIONS

 

The boiler is wired for 120 volts, single phase, 60 hertz.  
The total operating amperage is indicated on the rating 
nameplate.  Each MACH® C1500GG-C2000GG boiler 
requires less than 15 amps.  Before starting the boiler, 
check to ensure that the proper electrical service is 
connected to the boiler.   

An external electrical disconnect (not supplied with the 
boiler) is required.  The boiler electrical service must be 
installed and grounded in accordance with local codes or 
in the absence of such requirements, in the U.S. with 
National Electrical Codes, ANSI/NFPA No. 70 latest 
edition or, in Canada, to the Canadian Electrical Code, 
Part I, CSA C22.1, latest edition. Conduit must be installed 
vertically so that the side doors can be opened. 

 

NOTICE!

  A dedicated earth ground (green wire) and neutral is required to avoid nuisance shutdowns.  

Do not ground through the conduit.  It is also important that proper polarity be maintained. 

 

The electrical junction boxes are located at the front sides of the boiler.  A detailed schematic of the connections is 
shown in section 6.1. 

 

3.4.1  High Voltage (TB2) Terminal Block 

The boiler power circuit requires 120 VAC, 60 hertz, with a dedicated neutral and ground as labeled.  Electrical 
service must be rated for 8 amps minimum.  Before starting the boiler, check to ensure that the proper voltage and 
amperage are connected to the boiler and that the boiler is connected to a suitable fused disconnect switch or circuit 
breaker.  There must be less than 1.0V from Neutral (TB2-3) to Ground (TB2-8) 

 

 

120VAC Switched Output

- 

This contact closes when the boiler is switched on.  This provides 120VAC 5Amp 

service to TB2-10.  The neutral for this circuit is provided on TB2-3.   When the boiler is switched off, this terminal is 
switched off as well. 
 

3 Way Valve-

 

This output is normally energized, keeping the three way valve providing heat to the building.  The 

Domestic Hot Water (DHW) call for heat de-energizes this circuit, causing the 3 way valve to self close, thereby 

Type of Surface 

Dimensions (inches) 

A 

B 

C† 

D 

Combustible Surfaces 

Minimum Clearances 

18 

18 

18 

18 

Recommended Service 

Clearances 

30 

12* 

12 

18** 

TB1: Low Volt 
Junction Box 

TB2: 120 Volt 
Junction Box 

Customer Connections for the Boiler 

 Viewed from Front of Boiler. 

 

Summary of Contents for MACH C1500GG






























































Reviews:

No comments