manualshive.com logo in svg

Harsco Industrial MACH C1500GG, Installation & Owner'S Manual, Page: 5 / 61

Share
Download
Harsco Industrial MACH C1500GG Installation & Owner'S Manual Download Page 5

 

 

 

 
 
 

 

MACH® Gas-Fired Boiler 

 

 

Page  5 

 

Operating and service personnel must be thoroughly familiar with the basic construction of the MACH® boiler  
C1500GG or C2000GG, the use and locations of the controls, the operation of the boiler, adjustment of its various 
mechanisms, and all applicable safety precautions.  If any of the provisions of this manual are not fully and completely 
understood, contact Technical Service toll free at (877) 728-5351. 

 

2.3 

S

AFETY 

F

EATURES

 

It is the responsibility of the customer to maintain the safety features, such as but not limited to: guards, safety labels, 
safety controls, interlocks, lockout devices, in place and operable. 

 

2.4 

S

AFETY 

L

ABELS

 

The following words are used in this manual to de-note the degree of seriousness of the individual hazards.  

 

 

 

 

 

 

 

 

 

 

 

 

The safety labels shown above are affixed to your boiler.  Although the labels are of high quality, they may become 
dislodged or unreadable over time.  Contact Harsco Industrial, Patterson-Kelley toll-free at (877) 728-5351 for 
replacement labels.  

NOTICE/NOTE

 - NOTICE is the preferred signal word to address practices not related to personal injury. The 

safety alert symbol is not used with this signal word.

 

 

 indicates a potentially hazardous situation which, if not avoided, 

may

 result in minor 

or moderate injury.  It may also be used to alert against unsafe practices. 

 

 indicates a potentially hazardous situation which, if not avoided, 

could

 result in death 

or serious injury. 

 indicates an imminently hazardous situation which, if not avoided, 

will

 result in death 

or serious injury. This signal word is to be limited to the most extreme situations. 

Reorder No. 6020-V2WHPK

Improper use may
result in fire or injury.

Read instructions/safety
manual before installing, 
operating or servicing boiler.

c

!

WARNING

1998 HCS, Inc. 800-748-0241

Summary of Contents for MACH C1500GG






























































Reviews:

No comments