manualshive.com logo in svg

Harsco Industrial MACH C1500GG, Installation & Owner'S Manual, Page: 45 / 61

Share
Download
Harsco Industrial MACH C1500GG Installation & Owner'S Manual Download Page 45

 

 

 

 
 
 

 

MACH® Gas-Fired Boiler 

 

 

Page  45 

 

5.5.10  Manual Reset Error Codes 

– A## 

Code 

ENVI

™ Control Display 

Lockout  

Description 

A00 

NED 

Unassigned 

No Error Description, Call For Service 

A01 

IGNITION FAILURE 

Ignition Failure 

During an attempt to light, no flame was detected 

A02 

FLAME FAILURE 

Flame Failure 

During run, the flame was lost 

A03 

HIGH LIMIT 

High Limit 

The temperature in the boiler exceeded the setting on 
the High Limit Control 

A05 

INT ERR GAS VLV RLY 

Internal Error Gas Valve 
Relay 

Call for service. 

A06 

INT ERR SAFETY RLY 

Internal Error Safety Relay 

Call for service. 

A07 

LOW FLOW / ILK 

Low Water Flow or Open 
Interlock Jumper 

Water Flow is Inadequate or 
Interlock Jumper is Open 

A09 

INTERAL ERROR  
9 or 27 or 28 or 29 or 30 

Internal Error  
9 or 27 or 28 or 29 or 30 

Call for service. 

A10 

INT ERR E2PROM ERR 

Internal Error E2PROM Err 

Call for service. 

A12 

INT ERR E2PROM SIG 

Internal Error E2PROM Sig 

Call for service. 

A13 

INTERAL ERROR 13 

Internal Error 13 

Call for service. 

A14 

INTERAL ERROR 14 

Internal Error 14 

Call for service. 

A15 

INTERAL ERROR 16 

Internal Error 16 

Call for service. 

A16 

INTERAL ERROR 22 

Internal Error 22 

Call for service. 

A18 

INTERAL ERROR 19 

Internal Error 19 

Call for service. 

A19 

LATE FLAME 

Late Flame 

Flame still present after boiler gas valve closed during 
post purge 

A20 

EARLY FLAME 

Early Flame 

Flame detected before boiler gas valve opened during 
pre purge 

A30 

HIGH GAS PRESSURE 

High Gas Pressure Error 

The gas pressure is too high and has tripped the HGPS 
or both gas valves have opened at the same time 

A31 

LOW GAS PRESSURE 

Low Gas Pressure Error 

The gas pressure is too low and has tripped the LGPS 

A32 

INTERAL ERROR 23 

Internal Error 23 

Call for service. 

A33 

FAN WRONG SPEED 

Wrong Fan Speed Error 

Fan deviation more than 300 rpm for > 1 sec (ignored 
when fan > 4200 rpm) 

A34 

AIR SWITCH NOT OPEN 

Air Switch Not Open 

Air switch does not open when fan is off 

A35 

AIR SWITCH NOT CLOSE 

Air Switch Not Closed 

Air switch does not close when fan is running 

A37 

UV SENSOR DEFECT 

UV Sensor Defective 

Self Check function of UV detector has indicated a failure 

A38 

MAX DT EXCEEDED 

Max Delta Temp Exceeded 

Maximum temperature differential across the boiler has 
been exceeded 

A39 

RAPID RISE INLET TMP 

Rapid Rise Inlet Error 

Inlet temperature is rising too rapidly 

A40 

RAPID RISE OUT TEMP 

Rapid Rise Outlet Error 

Outlet temperature is rising too rapidly 

A41 

RAPID RISE HX TEMP 

Rapid Rise HX Temp 

Temperature across heat exchanger is rising faster than 
allowed 

A43 

LOW WATER LEVEL 

Low Water Cutoff 

Water is too low for boiler to operate 

A45 

INTERNAL ERROR 31 

Internal Error 31 

Call for service. 

Note:  When an Internal Error occurs, as identified above, the failu

re is internal to the ENVI™ boiler control and 

replacement of the ENVI™ control is required.  A qualified service technician must replace the ENVI™ control. 

Summary of Contents for MACH C1500GG






























































Reviews:

No comments