Harsco Industrial MACH C1500GG Installation & Owner'S Manual Download Page 47 | Manualshive

Page: 47 / 61

Harsco Industrial MACH C1500GG Installation & Owner'S Manual Download Page 47

MACH® Gas-Fired Boiler

Page 47

6.0 PARTS/TECHNICAL SUPPORT

Spare parts and replacement parts can be ordered from Harsco Industrial, Patterson-Kelley by calling toll free (877)
728-5351. The fax number is (570) 476-7247. Technical information is also available at the above number and at
the Harsco Industrial, Patterson-Kelly website www.harscopk.com.

Use of Non-Factory-Authorized replacement parts are not recommended for this

equipment. All control components are engineered for safety and are designed to work in unison with
each of the other components. Use of non-factory-authorized replacement parts jeopardizes the
functionality of the safety features as well as the performance of the boiler.

When ordering replacement parts please have the

model number

and

serial number

of your boiler available.

Typical schematic drawings are shown on the following pages. Drawings specific to your particular boiler can also be
supplied by your local Harsco Industrial, Patterson-Kelley representative.

6.1

W

IRING

D

IAGRAMS

6.1.1 Terminal Block Assignments

– High Voltage Circuit (TB2)

Terminal Number

Label

Description

1

120 VAC LINE

Boiler Supply Power, 120 VAC, 1 ph , 60 Hz

2

120 VAC NEUTRAL

Boiler Supply Neutral, 0 VAC

3

120 VAC NEUTRAL

Neutral for use with TB2-10, Switched Output

4

120 VAC NEUTRAL

Neutral for use with TB2-11, 3 Way Valve

5

120 VAC NEUTRAL

Neutral for use with TB2-12, DHW Pump Contactor

6

120 VAC NEUTRAL

Neutral for use with TB2-13, CIRC Pump Contactor

7

120 VAC NEUTRAL

Neutral for use with TB2-14, Damper Output

8

GROUND

Boiler Supply Ground, 0 VAC

9

GROUND

Boiler Supply Ground, 0 VAC

10

120VAC SW OUTPUT

120V AC output when boiler is switched on (4 amp
max)

11

120VAC 3 WAY VALVE

120V AC output during CH Mode. 3 way valve is
normally closed (not powered) for DHW, and powered
open for CH Mode.

12

120VAC DHW PUMP CNTR 120V AC output when boiler is in DHW Mode (pilot duty

only)

13

120VAC CIRC PUMP CNTR 120V AC output when boiler is in CH Mode (pilot duty

only)

14

120VAC DAMPER

120V AC output when boiler is enabled (pilot duty only)

15

MASTER ALARM RELAY

This circuit closes when the boiler is in an alarm state

16

MASTER ALARM RELAY

17

FLAME DETECTED RELAY This circuit closes when the boiler is firing

18

FLAME DETECTED RELAY

«
...
45
46
47
48
49
...
»

Summary of Contents for MACH C1500GG






























































Reviews:

No comments