background image

8

P68 Pellet Stove

venting

requirements for terminating the venting

WARNING: Venting terminals must not be recessed 

into a wall or siding.

NOTE: Only PL vent pipe wall pass-throughs and fire 

stops should be used when venting through combustible 

materials.

NOTE: Always  take  into  consideration  the  effects 

of the prevailing wind direction or other wind currents 

that may cause flyash and/or smoke when placing the 

termination vent.

in addition, the following must be observed:

A. The clearance above grade  must be a minimum 

of 18".

1

B. The clearance to a window or door that may be 

opened must be a minimum of 48" to the side, 48" below 

the window/door, and 12" above the window/door.

1

with outside air installed, 18” 

)

C. A 12"  clearance to a permanently closed window  

is    recommended  to  prevent  condensation  on  the 

window.

D. The vertical clearance to a ventilated soffit located 

above the terminal within a horizontal distance of 2 feet 

(60 cm) from the center-line of the terminal  must be a 

minimum of 18".

E. The clearance to an unventilated soffit  must be 

a minimum of 12".

F. The clearance to an outside corner is 11" from 

center of pipe.

G. The clearance to an inside corner is 12".

H.  A vent must not be installed within 3 feet (90 cm) 

above a gas meter/regulator assembly when measured 

from the horizontal center-line of the regulator.

1

I. The clearance to service regulator vent outlet must 

be a minimum of 6 feet.

1

J. The clearance to a non-mechanical air supply inlet 

to the building or the combustion air inlet to any other 

appliance must be a minimum of 48”.

1

K. The clearance to a mechanical air supply inlet must 

be a minimum of 10 feet.

1

(

with outside air installed, 6 feet 

)

L. The clearance above a paved sidewalk or a paved 

driveway located on public property must be a minimum 

of  7 feet.

1,2

M. The clearance under a veranda, porch, deck or 

balcony must be a minimum of 12 inches.

1,3

(See b.)

NOTE:  The clearance to vegetation and other exterior 

combustibles such as mulch is 36” as measured from 

the center of the outlet or cap. This 36” radius continues 

to grade or a minimum of 7 feet below the outlet.

1

Certain Canadian and or  Local codes or regulations 

may require different clearances.

2

A  vent  shall  not  terminate  directly  above  a  side-

walk or paved driveway which is located between two 

single  family dwellings and serves both dwellings.

3

Only permitted if veranda, porch, deck, or balcony is 

fully open on a minimum of  2 sides beneath the floor.

note: Where passage through a wall, or partition of 

combustible construction is desired, the installation 

shall conform to can/cSa-b365. (if in  canada)

= Vent terminal

v

Summary of Contents for P68













































Reviews: