background image

35

P68 Pellet Stove

4021-645C 12-29-10 

Page 1 of 2

Hearth & Home Technologies Inc.

LIMITED LIFETIME WARRANTY

Hearth & Home Technologies Inc., on behalf of its hearth brands (”HHT”), extends the following warranty for 

HHT gas, wood, pellet, coal and electric hearth appliances that are purchased from an HHT authorized dealer.

WARRANTY COVERAGE:

HHT warrants to the original owner of the HHT appliance at the site of installation, and to any transferee taking ownership 

of the appliance at the site of installation within two years following the date of original purchase, that the HHT appliance 

will be free from defects in materials and workmanship at the time of manufacture. After installation, if covered compo-

nents manufactured by HHT are found to be defective in materials or workmanship during the applicable warranty period, 

HHT will, at its option, repair or replace the covered components. HHT, at its own discretion, may fully discharge all of its 

obligations under such warranties by replacing the product itself or refunding the verified purchase price of the product 

itself. The maximum amount recoverable under this warranty is limited to the purchase price of the product. This warranty 

is subject to conditions, exclusions and limitations as described below.

WARRANTY PERIOD:

Warranty coverage begins on the date of original purchase. In the case of new home construction, warranty coverage 

begins on the date of first occupancy of the dwelling or six months after the sale of the product by an independent, 

authorized HHT dealer/ distributor, whichever occurs earlier. The warranty shall commence no later than 24 months 

following the date of product shipment from HHT, regardless of the installation or occupancy date. The warranty period for 

parts and labor for covered components is produced in the following table.
The term “Limited Lifetime” in the table below is defined as: 20 years from the beginning date of warranty coverage for 

gas appliances, and 10 years from the beginning date of warranty coverage for wood, pellet, and coal appliances. These 

time periods reflect the minimum expected useful lives of the designated components under normal operating conditions.

See conditions, exclusions, and limitations on next page.

Parts

Labor

Gas

Wood

Pellet

EPA

Wood

Coal

Electric Venting

X

X

X

X

X

X

X

All parts and material except as 

covered by Conditions, 

Exclusions, and Limitations 

listed

X

X

X

Igniters, electronic components, 

and glass

X

X

X

X

X

Factory-installed blowers

X

Molded refractory panels

X

Firepots and burnpots

5 years 1 year

X

X

Castings and baffles

7 years 3 years

X

X

X

Manifold tubes, 

HHT chimney and termination

10 

years

1 year

X

Burners, logs and refractory

Limited 

Lifetime 3 years

X

X

X

X

X

Firebox and heat exchanger

X

X

X

X

X

X

X

All replacement parts

beyond warranty period

Warranty Period

HHT Manufactured Appliances and Venting

1 Year

Components Covered

3 years

2 years

90 Days

Summary of Contents for P68













































Reviews: