1 -9 0 -0 9 7 3 0 R 2 6 _ 0 6 /1 3
Floor Protection
Floor Protection
Floor P
rot
ec
tion
Consult with your local building code agency and insurance
representative before you begin your installation to ensure
compliance with local codes, including the need for permits
and follow-up inspections.
Several issues must be addressed when selecting a suitable
location for your Advance Pellet Stove. Observing required
clearances to combustible materials, the proximity to a safe
chimney or venting system, and the accessibility of electrical
supply must all be considered. In addition, selecting a location
that takes advantage of the building s natural air flow is also
desirable to maximize the heating effectiveness of the heater.
In many cases, this is a central location within the building.
Place the stove on a noncombustible floor or a floor protector
that extends (152mm) to the front, (152mm) to the sides
and 1 (25mm) to the rear of the stove. In the US, the front
and side floor protection is measured from the door opening.
In Canada, the measurements are from the appliance. ( ig. 8.)
loor protection must be placed under any horizontal venting.
This protection must extend a minimum of 2 (51mm) beyond
each side of the pipe.
n ana a y u may
ma er S
r pr tect n
req uirements ONLY if the user agrees to completely
shut-down the appliance, and allow it to cool to where all
fire e t n u
e an t e c m u t n
er an t
n cat r
t ut
pr r t pen n t e fire
r
or ash door.
Place the stove away from combustible walls at least as far as
shown in figures , and 7. The clearance to a ceiling above the
appliance is 2 ( 08mm).
Note that the clearances shown are minimum for safety, but
do not leave much room for access when cleaning or servicing.
Please take this into account when placing the stove.
Mobile Home Installation
When installing this stove in a mobile home several
requirements must be followed:
1. The unit must be bolted to the floor. This can be done with
1 lag screws through the 2 holes in the base plate shown
in ig. 11, Page 10.
2. The unit must also be connected to outside air. See page 1 .
. loor protection and clearances must be followed as shown.
. Unit must be grounded to the metal frame of the mobile
home.
5. WARNING - O NOT INSTALL IN A SLEEPING ROO .
CAUTION: This appliance must be vented to the outside.
The factory-built chimney must conform to CAN ULC-S 2 ,
Standard for 50 C actory-Built Chimneys. Use the vent or
chimney manufacturer s components to provide an effective
vapor barrier where the vent penetrates to the exterior.
The top section(s) of chimney must be removable to a maximum
height of 1 ( . ) to allow transport.
Installation and repair of this stove should be done by a
qualified service person. The appliance should be inspected
before use and at least annually by a qualified service person.
requent cleaning will be required. It is imperative that control
compartments, burners, and circulating air passageways of
the stove be kept clean.
Installation
CAUTION
T H E S T R U C T U R A L I N T E G R I T Y O F T H E
MANUF ACTUR ED HOME F LOOR , W ALL, AND CEILING /
R OOF MUST BE MAINTAINED.
CAUTION
HOT W HILE IN OPER ATION.
K EEP CHILDR EN, CLOTHING , AND F UR NITUR E AW AY .
CONTACT MAY CAUSE SK IN BUR NS.
ig. 7
1 0 "
2 5 4 mm
1 "
2 5 mm
L
J
F loor Protection
R eq uirements
US
Canada
Sides
Rear
200mm
1
200mm
K
ront
50mm
J
Canada
J
USA
K
L
NOTE:
easurement
is measured
from the glass
in the US ONLY
7"
/ 1
78
mm
7 " / 1 7 8 mm
ig.
Alternate floor protector
dimension may be used
as long as they satisfy the
measurement requirements
shown below.
Minumum size floor protection
for a corner installation hearth
pad is 36" x 36".
The Clearance to The Top of The Unit is 0 (152cm)
easured rom The loor.
