Hardi HC5500 Instruction Book Download Page 9 | Manualshive

Page: 9 / 80

background image

9

2 - Safety notes

Operator safety

€

This symbol means DANGER. Be very alert as your safety is involved!

±

This symbol means WARNING. Be alert as your safety can be involved!

μ

This symbol means ATTENTION. This guides to better, easier and more safe operation of your sprayer!

÷

This symbol means NOTE.

General info

€

Note the following recommended precautions and safe operating practices.

€

Read and understand this instruction book before using the equipment. It is equally important that other operators
of this equipment read and understand this book.

€

Keep children away from the equipment.

€

If any portion of this instruction book remains unclear after reading it, contact your HARDI dealer for further
explanation before using the equipment.

€

Turn electrical power off before connecting and disconnecting the display and transducers, servicing or using a
battery charger.

€

If an arc welder is used on the equipment or anything connected to the equipment, disconnect power leads before
welding.

€

Test with clean water prior to filling with chemicals.

€

Do not use a high pressure cleaner to clean the electronic components

€

Press the keys with the underside of your finger. Avoid using your fingernail.

«
...
7
8
9
10
11
...
»

Summary of Contents for HC5500

















































































Reviews:

No comments

Related manuals for HC5500

Brand: Panasonic Pages: 31

Brand: Panasonic Pages: 31

Brand: Panasonic Pages: 26

Brand: NAiS Pages: 199

Brand: Panasonic Pages: 38

Brand: Panasonic Pages: 64

Brand: Panasonic Pages: 36

Brand: Panasonic Pages: 179

Brand: Panasonic Pages: 23

Brand: Panasonic Pages: 30

Brand: Panasonic Pages: 26

Brand: Panasonic Pages: 12

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 44

Brand: Panasonic Pages: 20

INDUSTRY PAN9028

Brand: Panasonic Pages: 34

COOPER POWER SERIES

Brand: Eaton Pages: 50

Brand: Ebyte Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands