Hardi HC5500 Instruction Book Download Page 15

Page: 15 / 80

3 - Description

Keys

General key description

The HC 5500 controller buttons are placed in three groups; navigation
keys, shortcut keys, distance key and the auto key.

The shortcut keys can be used for the following:

Short press: Displays volume sprayed for the active register.

Long press: Enter Register select (menu 1.3.1 Register select).

Short press : Displays the actual speed.

Long press: Enter Speed calibration (menu 3.1.1 Speed).

Short press: Displays the actual tank contents.

Long press: Enter Tank contents menu (menu 1.2 Tank contents).

Short press: Show Area covered for active register.

Long press: Enter Register select (menu 1.3.1 Register select).

Short press: Show the selected volume rate.

Long press: Enter Volume rate menu (menu 1.1 Volume rate).

Short press: Shows remaining spraying distance with actual tank contents.

Long press: Enter Measure distance menu (menu 4.1.1 Distance).

Pressing

will: Enable Autofunction.

Summary of Contents for HC5500

















































































Search results

Summary of Contents for HC5500

Reviews:

Related manuals for HC5500

Brands by name

Popular brands

Hardi HC5500, Instruction Book

Search results

Summary of Contents for HC5500

Reviews:

Related manuals for HC5500

Brands by name

Popular brands