Hardi Commander Twin Force Plus Instruction Book Download Page 72

Page: 72 / 94

GB 14 08 01

Maintenance

To change a bulb

1. Switch off the light

2. Loosen the screws on the lamp and remove the cover

or lens.

3. Remove the bulb

4. Fit a new bulb, refit the cover and tighten the screws.

NOTE!

If halogen bulbs are used, never touch the bulb

with the fingers. Natural moisture in the skin will cause

the bulb to burn out when the light is switched on.

Always use a clean cloth or tissue when handling

halogen bulbs.

Adjustment of

Adjustment of slanting indica

slanting indica

slanting indicator

tor

If the position of the pointer on the indicator does not

correspond to the actual boom position, the pointer

can be adjusted.

1. Loosen the small bolt

sufficiently to allow the wire

to be adjusted.

2. Place the pointer

correct position and fasten

bolt

against the wire

again.

T112-0008x

TTrrrrransmission shaft, shield r

ansmission shaft, shield r

ansmission shaft, shield rene

ene

enew

wal

The replacement of defective shields is done as follows:

1. Push down on the

universal cross

cover and press in

the tabs with a

screwdriver. Maintain

pressure until all

three tabs are

released.

2. Remove the nylon

bearing and pull off

the protection tube.

3. Grease protection

tube bearing groove

on the inner yoke.

4. Slide on the shield

tube and fit the

bearings tabs into

the slots.

5. Slide the universal

cross cover over the

protection tube and

align the grease

nipple with the

grease channel on

the bearing. Press

the universal cross

cover onto the tabs

until they lock.

6. Check alignment

and locking of the

tabs by tapping the

universal cross

cover lightly.

Constant Velocity joint shielding

1. Remove the screws

holding the two

halves of the shield

together.

2. Separate the shield

and remove it from

the joint. Check and

replace any worn or

damaged parts.

T269-0006

T269-0007

T269-0008

T269-0003

T269-0004

T269-0005

T269-0009

T269-0010

Summary of Contents for Commander Twin Force Plus































































































Search results

Summary of Contents for Commander Twin Force Plus

Reviews:

Related manuals for Commander Twin Force Plus

Brands by name

Popular brands

Hardi Commander Twin Force Plus, Instruction Book

Search results

Summary of Contents for Commander Twin Force Plus

Reviews:

Related manuals for Commander Twin Force Plus

Brands by name

Popular brands