Hardi Commander Twin Force Plus Instruction Book Download Page 30

Page: 30 / 94

GB 07 02

Operation

Oper

Operaaaaating the boom

ting the boom

WARNING:

Be cautious with initial use of the

hydraulic system. If there is air in the system this

may cause violent movements of the boom.

Therefore, take care that no persons or objects are hurt

or damaged in the process of testing.

DANGER! When folding

and unfolding the boom,

be sure that no persons

or objects are in the

operating area of the

boom, and that the boom

cannot touch any electri-

cal conductors!

TThe HA

he HA

he HAY boom

Y boom

The boom unfolding/folding can be done according to

instructions below.

1.Lift up the boom lift until the boom is clear of the

transport brackets using the single acting spool valve

2.Unfold the boom completely using the double acting

spool valve

3.Lower the boom to correct working height above the

ground/crop 50 cm/20 in

Folding is to be done in reverse order.

TThe HAZ boom

he HAZ boom

(If the sprayer is equipped with HARDI NOVA , please

see separate instruction book for operating instructions).

Functions of the control box:

Raising and lowering of boom

Unfolding/folding of inner sections

Unfolding/folding of outer sections

Slanting of boom

Angling of air slot/nozzle assembly

Boom tilt, RH

Boom tilt, LH

Fan speed adjustment

Drawbar mode (STEER TRACK only)

The boom unfolding/folding can be done according to

instructions below:

Unfolding the boom

NOTE!

Ensure that the transport safety chains are

removed and the boom is clear from the transport

brackets before unfolding.

1.Push switch

upwards to lift the boom clear of the

transport brackets.

2.Push switch

upwards to unfold the inner sections.

Rear transport hooks disengage automatically.

3.Push switches 6 and 7 downwards to lower individual

tilt rams.

4.Push switch

upwards to unfold outer sections.

5.Push switch

to correct slant angle.

6.Push switch

downwards to lower the boom to correct

height above crop or ground level.

7.In order to reduce wind drift and/or increase penetra-

tion of spray liquid in the crop, the slot angle can be

changed backwards and forwards with switch

IMPORTANT!

The two upper functions in the red rectan-

gle with STOP signs must only be operated when the

sprayer is stationary! Failure to do so will damage the

boom.

Folding the boom

1.Check that the slanting function is midway

2.Set slot angle at midway

3.Raise boom

to upper position.

4.Fold outer sections

5.Lift individual boom tilt

and

6.Fold inner sections

. Rear transport hooks

engage automatically.

7.Lower boom

until boom rests on transport

brackets.

Hydraulic slanting control

The hydraulic slanting control

enables slanting of the

entire boom hydraulically. This is advantageous when

spraying across hillsides.

Reset position to neutral (midway) before folding the

boom.

Boom tilt function

The boom tilt function control

and

enables you to

adjust the boom height individually in right and left-hand

side.

Air slot angling

The air slot and nozzle assembly can be angled approx.

40º forwards and 30° backwards compared to vertical

position. Regarding adjustments - see section on

Air technique.

T029-0010

T030-0004

Summary of Contents for Commander Twin Force Plus































































































Search results

Summary of Contents for Commander Twin Force Plus

Reviews:

Related manuals for Commander Twin Force Plus

Brands by name

Popular brands

Hardi Commander Twin Force Plus, Instruction Book

Search results

Summary of Contents for Commander Twin Force Plus

Reviews:

Related manuals for Commander Twin Force Plus

Brands by name

Popular brands