background image

9

Lowes.com/harborbreeze

INITIAL INSTRUCTIONS  

WIRING INSTRUCTIONS

      

      

WARNING: 

To avoid possible electrical shock, be sure electricity is turned off at the main fuse 

box before hanging. 

      

      

WARNING: 

If you are not sure if the outlet box is grounded, contact a licensed electrician for 

advice, as it must be grounded for safe operation.

1.  Connect the GREEN wires from the hanger ball of 

     downrod assembly (B) and mounting bracket (A) to the 

     supply ground (GREEN or bare color). Securely connect 

     wires using wire connector (AA) supplied.

      

      

WARNING:

 If house wires are different colors than referred to in the following steps, stop 

immediately. A professional electrician is recommended to determine proper wiring.

      

      

WARNING:

 If you feel that you do not have enough electrical wiring knowledge or experience, 

have your fan installed by a licensed electrician.

9

A

B

9.  Carefully lift the assembly and rest the hanger ball of 

     downrod assembly (B) on the mounting bracket (A) 

     attached to the outlet box.

NOTE: 

Unlike a standard circular fan, the mounting 

bracket (A) for this item does not have a tab, which 

locks the fan into a specific position. This allows you 

the  freedom to rotate the fan's linear motor housing 

360°so it can be correctly oriented with the layout of 

your room.

Hardware Used

x 1

AA

Wire Connector

A

B

AA

1

Supply 

Ground Wire

Green Wire

from A

Green Wire from

Hanger Ball

Summary of Contents for L0982




















Reviews: