background image

Preliminary Examination

1.  PRELIMINARY EXAMINATION

Remove the probe and accessories from the packing and examine it carefully. 
Each probe is supplied with:

• 

HI764113-1

 DO Smart Cap with O-ring

•  Calibration beaker
•  Sachet with silicone grease
•  Syringe
•  Quick reference guide with probe quality certificate

Note

: Save all packing material until you are sure that the probe works correctly. Any damaged or defective item 

must be returned in its original packing material with the supplied accessories.

2.  SAFETY MEASURES

General Safety & Installation Recommendations

•  Electrical connection, installation, operation, and maintenance must be carried out by specialized 

personnel only. 
The specialized personnel must read, understand, and adhere to the instructions in this manual. 

•  Before connecting the probe to the process controller, disconnect the controller from the power line.
•  User serviceable connections are all accessible inside controller’s enclosure.
•  Before powering the controller, verify the probe wiring has been done following the instructions 

detailed in this manual.

3.  GENERAL DESCRIPTION & INTENDED USE

The 

HI7640-58

 series are optical dissolved oxygen probes with Smart Caps (

HI764113-1

) for measurement 

of dissolved oxygen.
The series is designed to work with the Hanna Instruments

®

 

HI510

 Universal Process Controller. When paired with 

the controller, the system provides accurate dissolved oxygen measurements auto-compensated for barometric 
pressure, salinity (set manually), and temperature.
Suitable for control applications in aeration basins, ponds, and tanks where optimizing oxygen transfer is a 
key element, the probe can be submersed/immersed in a tank using the 

3/4

” NPT threads, or installed in a 

flow cell using the lower sensor threads.
The probe is available with an 

integral connector

 that permits connections with no twisted cables as cables 

are connected after installation.

Patch cables

 may be purchased separately to connect between the probe and controller up to 50 meters (164 ft).

Summary of Contents for HI7640-58

















Reviews: