background image

 

MAN3041-1 

 

 

 

 

12

 

6.4

 

Technical Data: 

Specifications are typical and given at 23°C and 50% relative humidity unless specified otherwise. 

 

 

Detector 

operating 

principle: 

Photo electric detection of light scattered by smoke particles over a wide range 
of angles. The optical management comprises an infra-red emitter with a prism 
and  photo-diode  at  90°  to  the  light  beam  with  a  wide  field  of  view.  The 
detectors microprocessor uses algorithms to process the sensor reading. 
The  heat  sensing  element  increase  the  sensitivity  of  the  detector  as  the 
temperature rises. 

Sampling frequency: 

Once every 4 seconds 

Supply voltage: 

14-28V dc 

Supply wiring: 

2 wires, polarity sensitive 

Polarity reversal:  

Not allowed 

Power-up time: 

<20 seconds 

Minimum 

detector 

active voltage: 

12V dc 

Switch-on surge current: 

105µA at 24V dc 

Quiescent current: 

85µA at 24V dc 

Alarm load: 

325

 in series with 1.0V drop 

Material: 

Detector and base moulded in white polycarbonate 

Alarm Indicator: 

Integral indicator with 360° visibility 

Dimensions  and  weight 
of detector: 

100mm diameter x 50mm H 
80g 

Dimensions  and  weight 
inc base: 

100mm diameter x 60mm H 
140g 

Operating  and  storage 
temperature:  

-40°C to +70°C 
Operating temperature is restricted by the intrinsic safety gas classification. 
Class T5: - 40°C to +40°C Class T4: - 40°C to +60°C 
The detector must be protected from conditions of condensation or icing. 

Humidity: 

0% to 98% relative humidity (no condensation) 

Wind speed: 

Unaffected by wind 

Atmospheric pressure: 

Insensitive to pressure 

IP rating: 

23D to EN60529:1992* 

Electromagnetic 
compatibility: 

The detector meets the requirements of BS EN61000-6-3 for emissions and BS 
EN50 130-4 for susceptibility. 

 

*  The  IP rating is not a requirement of EN54-7: 2000 since  smoke detectors have  to be  open in order  to 
function. An IP rating is therefore not as significant as with other electrical products.  

 

 

  

Summary of Contents for Ampac Orbis IS ORB-OP-52027-APO


























Reviews: