background image

•  Includes LCC27 SafeLok regulator and hose
•  Traditional style smoker for delicious smoking 

and slow cooking of foods

• 10.5 MJ/h Burner
• 3 Adjustable chrome plated wire racks
• 6 Hanging meat hooks
• Vitreous enamel smoker box
• Door mounted thermometer
• 2 Side handles that double as tool hooks
•  Includes water bowl and smoker box to add 

moisture and flavour when cooking

• Hose and regulator included
• For outdoor use only
• Universal LPG
• Gas certified to Australian Standards
• Size: 550mm W x 490mm D x 1030mm H

Important: Retain these instructions for future use.

04398 02/22

Gasmate® is a registered trademark of  

Sitro Group Australia Pty Ltd www.gasmate.com.au 

Aber Living, N.Z. www.gasmate.co.nz

FOR OUTDOOR USE ONLY 

WARNING: 

Improper installation, adjustment, alteration, service or 
maintenance can cause injury or property damage.
Read the instructions thoroughly before installing or 
servicing this equipment.

LCC27 REGULATOR 

SUPPLIED

This LCC27 Regulator can only be used 
with the new safer industry standard 
LCC27 Gas Cylinder Connection. 

GAS 

SMOKER

Model No. JBQ2056G

Summary of Contents for JBQ2056G





















Reviews: