background image

 Change setting temperature and offset temperature

Set  Temp

Offset 

 

Temp

Preset  Temp

Preset  ID

Ch  Power

Exit

350

00

ON

CH1

1. Turn the control knob and highlight SET TEMP for the setting temperature or OFFSET TEMP for the 

offset temperature, and press the control knob to change the setting.

Set  Temp

Offset 

 

Temp

Preset  Temp

Preset  ID

Ch  Power

Exit

350

00

ON

CH1

Setting temperature

Offset temperature

2. SET TEMP will begin adjusting from the highest possible setting digit; OFFSET TEMP will start with either 

a blank space, representing a positive (+) value, or a '-' for a negative value.

3

50

Setting

Temperature

Setting temperature

Offset temperature

Setting

Temperature

 

00

3. Turn the control knob to change the value of the selected digit, and press the control knob to accept the 

value and move to the next digit. (The figure below is an example using the SETTING TEMPERATURE 

display.)

3

50

Setting

Temperature

4

50

Setting

Temperature

4

50

Setting

Temperature

4

5

0

Setting

Temperature

4. After the last digit has been accepted by pressing the control knob, the screen will return to the previous 

menu.

40

0

Setting

Temperature

 Setting the preset temperature

PRESET1

PRESET2

PRESET3

300

350

400

E x i t

CH1

Preset  Set

Set  Temp

Offset 

 

Temp

Preset  Temp

Preset  ID

Ch  Power

Exit

350

00

ON

CH1

1. Turn the control knob, select "Preset Temp," and press the control knob when you have made your 

choice.

2. Turn the control knob, and make your choice by selecting the desired preset from the three options 

shown and pressing the control knob.

3

00

PRESET1

Temperature

PRESET1

PRESET2

PRESET3

300

350

400

E x i t

CH1

Preset  Set

Set  Temp

Offset 

 

Temp

Preset  Temp

Preset  ID

Ch  Power

Exit

350

00

ON

CH1

Changing the value for each selected preset follows the same steps as when changing the SET TEMP.

For the third digit of the 

offset temperature, select 

(blank) or -.

5. OPERATION

5

Summary of Contents for fm-206




















Reviews:

Related manuals for fm-206