background image

The tip may be hot. Avoid holding the hot tip for a long time even if 

using the heat-resistant pad. Otherwise burns may result.

CAUTION

Removing the tip:

 Hold down the lock release buttons in the sleeve assembly, pull out 

the tip together with the sleeve assembly from the connector.

 While holding the front end of the sleeve assembly, pull out the tip.

• Be sure to keep the lock release buttons held down while pulling 

out the sleeve assembly. Failure to do so will damage the locking 

mechanism.

• Be sure to pull out the tip only after separating the sleeve assembly 

from the connector. Otherwise, the sleeve assembly may fall down 

and break.

CAUTION

Insert the tip:

 

Reassemble in the reverse order of disassembly.

• Insert the tip into the sleeve assembly until it clicks into place. When 

you hear it click, avoid forcing the tip into the sleeve assembly.

• When holding the head of the tip, there is a danger of burn. Be sure 

to use the heat-resistant pad.

CAUTION

*Each Hakko handpiece with the exception of the HAKKO 

FM-2027 has their own instruction manual. Please refer to 
this manual for specifications and replacement parts.

Switch, Control Button and Knob Usage

Power switch

Use the power switch to turn 

the power on and off.

Control Buttons

Use to change settings such as 

temperature.

When pressed briefly:

Displays the preset screen.

When pressed and held:

Displays the change settings 

screen.

Change Settings Screen Details

1. Temperature Settings 

2. Offset Settings 

3. Preset Temperature Settings 

4. Preset Names 

5. Channel Power (On/Off) 

6 Exit

Control Knob Usage 

Use to change settings 

Turning the control knob:

Changes setting values 

or moves the cursor 

Pushing the control knob: 

Makes selection

* If you press a control button while on the Preset or Change

Settings screen, the corresponding channel screen will be 

displayed.

Plugged in irons will be heated according to the settings 

when the power is turned on.

Flow Control Knob 

When HAKKO FM-2029 is connected to 
HAKKO FM-206, air flow will be displayed. 
By turning the flow control knob, air flow 
can be changed. 

CH1

   

CH2

   

CH3

350

  

Off

  Ready

SOL

100%

M

Replacing the tip (HAKKO FM-2027)

4. INITIAL SETUP

3

Summary of Contents for fm-206




















Reviews: