background image

2

Maximizer

®

 97 Owner’s Manual

OR-05/18/15

Quality Water International 

®

15 Year  Limited Warranty

Coverage

To place this equipment under warranty, the warranty registration card must be completed and returned 

by the original owner to Hague Quality Water International within 30 days of installation.

This warranty covers the Hague 

97 Maximizer

®

 Appliance 

delivered to the original owner when the appliance is purchased 
for personal, family, or household use. It is intended to cover 
defects occurring in workmanship or materials or both.

Warrantor’s Performance and Length of Warranty

Hague Quality Water International warrants that upon receipt 
from the owner of any Hague Media Tank, Brine Tank, or Main 
Control Valve found to be defective in material or workmanship, 
Hague will repair or replace the defective item, at no charge for 
that item, for 15 YEARS from date of installation.

Hague Quality Water International further warrants that upon 
receipt from the owner of any other mechanical or electronic 
parts, and fine mesh polystyrene resin, which are found to be 
defective in material or workmanship, Hague will repair or replace 
the defective parts, at no charge for those parts for 5 YEARS 
from date of installation.

All defective parts must be returned, along with the equipment 
serial number and date of original installation, to an authorized 
Hague dealer of Hague Quality Water International PREPAID, 
and replacement parts will be returned by Hague to the owner 
FREIGHT COLLECT.

Further Exclusions and Limitations on Warranty:
This warranty is null and void unless the Hague Appliance 
was purchased from an independent Hague dealer. THERE 
ARE NO WARRANTIES OTHER THAN THOSE DESCRIBED IN 
THIS WARRANTY INSTRUMENT.

This warranty does not cover any service call or labor costs 
incurred with respect to the removal and replacement of any 
defective part or parts. Hague Quality Water International will not 
be liable for, nor will it pay service call or labor charges incurred 
or expended with respect to this warranty.

In the event the water supply being processed through this product 
contains sand, bacterial iron, algae, sulfur, tannins, organic 
matter, or other unusual substances, then unless the appliance 
is represented as being capable of handling these substances in 
the appliance specifications, other special treatment of the water 
supply must be used to remove these substances before they 
enter this product. Otherwise, Hague Quality Water International 
shall have no obligations under this warranty.

This warranty does not cover damage to a part or parts of the 
appliance from causes such as fire, accidents, freezing, or 
unreasonable use, abuse, or neglect by the owner.

This warranty does not cover damage to a part or parts of the 
appliance resulting from improper installation. All plumbing 
and electrical connections should be made in accordance with 
all local codes and the installation instructions provided with 
the appliance. The warranty does not cover damage resulting 
from use with inadequate or defective plumbing; inadequate 
or defective water supply or pressure; inadequate or defective 
house wiring; improper voltage, electrical service, or electrical 
connections; or violation of applicable building, plumbing, or 
electrical codes, laws, ordinances, or regulations.

THIS WARRANTY DOES NOT COVER INCIDENTAL, 
CONSEQUENTIAL OR SECONDARY DAMAGES. 

ANY IMPLIED WARRANTIES ON THE PRODUCT DESCRIBED 
IN THIS WARRANTY WILL NOT BE EFFECTIVE AFTER THE 
EXPIRATION OF THIS WARRANTY.

No dealer, agent, representative or other person is authorized to 
extend or expand this limited warranty.

Some states do not allow limitations on how long an implied 
warranty lasts or the exclusion or limitation of incidental or 
consequential damages, so the above limitations and exclusion 
may not apply to you. This warranty gives you specific legal rights 
and you may also have other rights which vary from state to state.

Claims Procedure

Any defects covered by this warranty should be promptly reported 
to Hague Quality Water International at 4343 S. Hamilton Rd. 
Groveport, OH 43125. In writing about the defects, please provide 
the original owner’s name, telephone number, and original 
address; serial number and model number of the product; date 
of purchase; and name of dealer from whom purchased. Hague 
Quality Water International reserves the right to replace defective 
parts with exact duplicates or their equivalent.

Summary of Contents for MAXIMIZER 97 Series





































Reviews: