Page 2 of 8
2916P Proximity Keypad
Installation Instructions
I-EA00130
Rev 6, Rev Date: 5/29/19
Always visit www.hagerco.com for the latest Installation Instructions
HAGER COMPANIES 139 Victor Street, St. Louis, MO 63104 • (800) 325-9995
Test your new user
Present your card or enter an authorized PIN code + #. The green indicator should
illuminate and the main relay should activate, unlocking the door for 5 seconds.
Fig. 2 Wiring Pigtail Color Code
}
AUXILIARY RELAY
2 AMPS @ 28VDC MAX
NO
COM
ORANGE
WHITE
BLACK
NC
TO POWER SUPPLY
KEYPAD POWER
12 or 24 VOLTS
AC OR DC
}
+
-
RED
BLACK
MAIN RELAY
5 AMPS @ 28VDC MAX
}
NO
COM
NC
ORANGE
WHITE
YELLOW
Set default parameters (first time use)
Step 1. Enter:
#9# 123456#
Enter programming mode (default master code=123456)
Step 2. Enter:
03# 4#
Set the entry code length to 4 digits
Step 3. Enter:
21# 5#
Set the main relay activation time for 5 sec.
Step 4. Enter:
#
Exit programming mode
**
Assign a user (PIN only)
Step 1. Enter:
#9# 123456#
Enter programming mode (default master code)
Step 2. Enter:
01# 003# 2580# 2580# 1#
Assign User 003 with a PIN code of
‘2580’.
Activate the main relay when entered.
Step 3. Repeat Step 2 to enter another unique user & PIN or continue to Step 4.
Step 4. Enter:
#
Exit programming mode
**
Deleting a user code
Step 1. Enter:
#9# 123456#
Enter programming mode (default master code)
Step 2. Enter:
02# 002# 002#
User 002 has been deleted.
Step 3. Enter:
#
Exit programming mode
**
QuickStart Programming
You must first enter programming mode to perform any function. The yellow indicator will blink slowly showing that the 2916P is
in programming mode. Use the option codes to program each function. After the new data entry is complete for each function ,
the yellow indicator will flash quickly while the data is being stored and the green indicator will light briefly if the programming has
been accepted. The red indicator will light if any programming data is entered incorrectly or the function is rejected. If a red
indicator is seen, the entire function (option code + data) will have to be fully re-entered. The keypad will remain in programming
mode until # is pressed or after 30 seconds of inactivity.
**
KEYPAD
POWER
WIRE
HARNESS
(E1-E8)
MAIN
RELAY
AUXILIARY
RELAY
ANTI-TAMPER
SWITCH
BACK
JP1
E1
E8
JP2
Grn Wire
To earth ground
BLACK
PINK/SALMON
GREEN
GRAY
BLACK
VIOLET
BLACK
BLUE
DOOR POSITION
SWITCH
[N/C]
REQUEST-TO-EXIT
SWITCH
[N/O]
GROUND
OUTPUT #4
OUTPUT #3
GROUND
SENSE
REQUEST TO EXIT
GROUND
E
1
E
8
E
7
E
6
E
5
E
4
E
3
E
2
C
NO
C
NC
NO
AUXILIARY OUTPUTS
100mA MAX TO COMMON
{
*
*
NOT USED
CAUTION
IF THE UNIT IS AC POWERED, MAKE SURE
THAT THE SECONDARY OF THE SYSTEM IS
ISOLATED FROM EARTH GROUND
!
!
RED/GREEN
POWER/ACCESS/ERROR
INDICATOR
YELLOW
“
PROGRAM
”
INDICATOR
KEYPAD
FRONT
PROX
Antenna
Assign a user (Card only)
Step 1. Enter:
#9# 123456#
Enter programming mode (default master code)
Step 2. Enter:
06# 002# 9876# 9876# 1# (Present card)
Assign card to User 002 with a
PIN code of
‘9876’.
Activate
the main relay when validated.
Step 3. Repeat Step 2 to enter another unique user & card, or continue to Step 4.
Step 4. Enter:
#
Exit programming mode.
**
