Page 3 of 8
2916P Proximity Keypad
Installation Instructions
I-EA00130
Rev 6, Rev Date: 5/29/19
Always visit www.hagerco.com for the latest Installation Instructions
HAGER COMPANIES 139 Victor Street, St. Louis, MO 63104 • (800) 325-9995
KEYPAD WIRING
See Fig. 3 for an example of a basic door installation. The keypad is mounted
adjacent to the door. An electric door strike is mounted in the door jamb to
release the door lock. A door contact switch is mounted on top of the door
jamb for detecting when the door is open.
Use the following steps to wire the keypad. Refer to the wiring diagram
shown in Fig. 4 to assist in the wiring.
Note: For lock power, use 18 AWG wire or larger (depending on load). Use
22 AWG or larger for signal connections. Refer to lock manufacturer
’
s
documentation for lock power requirements.
Output Connection
Install a low-voltage fail-secure electric door strike at the door to be controlled.
Route 2 wires from the door strike to the keypad. Connect an MOV across the
coil wires of the strike. Connect the (+) door strike wire to the keypad
’
s MAIN
RELAY N.O wire (yellow). Connect the other door strike wire to the keypad
’
s
PWR(-) wire (black). Connect the keypad
’
s MAIN RELAY COM wire (white)
to the keypad
’
s PWR(+) wire (red) .
Power Connection
Connect the power supply
’
s output terminals to the keypad
’
s PWR(+) wire
(red) and PWR(-) wire (black). If using a DC supply, observe wiring polarity. If
an AC transformer is being used, polarity does not mater.
Caution: If the unit is AC powered, make sure the secondary of the
system transformer is isolated from earth ground.
Earth Ground
To avoid damage to the unit from static discharges, this unit must be
connected to a proper earth ground. Connect the green earth ground wire to
a good earth grounding point. Suggested wiring size is 18 AWG for earth
ground.
Fig. 5 Using Solid State Outputs
Fig. 3 Basic Door Installation
OUTPUT #3 LIGHTS AN LED
OUTPUT #4 LIGHTS AN LED AND SOUNDS A BEEPER
EXAMPLE #1:
POWER
SUPPLY
+
LED
LED
BLUE
PINK/SALMON
1K
Ω
1K
Ω
-
+
OUTPUT #3
OUTPUT #4
ELECTRONIC
BEEPER
OUTPUT #3 LIGHTS A LAMP POWERED FROM AN EXTERNAL SOURCE
OUTPUT #4 TRIGGERS A NORMALLY OPEN ALARM PANEL ZONE
EXAMPLE #2:
BLUE
PINK/SALMON
OUTPUT #3 COM
OUTPUT #4 COM
POWER
SOURCE
OUTPUT #3
END OF LINE
RESISTOR
ALARM PANEL
NO ZONE
COMMON
LOW
VOLTAGE
LAMP
-
+
BLACK
BLACK
OUTPUT #4
EACH
OUTPUT
100 mA
MAXIMUM
W
ir
e
P
ig
ta
il
W
ir
e
P
ig
ta
il
Fig. 4 Basic Door Installation Wiring
Sense Input
RE
Note: The SENSE input (gray wire) can be programmed as either a door
sense or inhibit input. Both features cannot be used at the same time. If you
are not using the sense input, program this input for inhibit.
Door Sense: (Detect forced entry or door ajar conditions) Install a
normally
closed
door switch on the door and route two wires from the switch to the
keypad. Connect the door switch to the keypad
’
s SENSE wire (gray/ E8) and
COM wire (any black wire).
Inhibit: (Disable access) If an inhibit switch or timer is going to be used for
temporarily disabling the keypad, route two wires from the switch or timer to
the keypad. Connect the inhibit switch/timer
’
s
normally open
contacts to the
keypad
’
s SENSE (gray/ E8) and COM (black wires) terminal.
Request-to-Exit Input
(wiring shown on page 3, fig. 4)
If a request-to-exit pushbutton is going to be used, route two wires from the
keypad box to a normally open pushbutton mounted on the secure side of the
door. Connect the wires to the pushbutton and to the keypad
’
s REX wire
(violet/ E6) and COM (black wires) terminals.
Solid State Outputs
The two solid state outputs (Outputs #3 & #4) can be programmed to activate
during various conditions. These
“
open collector
”
outputs can be used to
activate indicators or sounders. See fig. 5 for wiring examples using the solid
state outputs.
TO POWER SUPPLY
KEYPAD POWER
12 or 24 VOLTS
AC OR DC
}
+
-
RED
BLACK
AUXILIARY
RELAY
2 AMPS @ 28VDC
MAX
}
NC
NO
COM
ORANGE
WHITE
BLACK
FAIL SECURE CONNECTION
FAIL SAFE CONNECTION
MAIN RELAY
5 AMPS @ 28VDC
MAX
}
NC
COM
NO
ORANGE
WHITE
YELLOW
BLACK
PINK/SALMON
GREEN
GRAY
BLACK
VIOLET
BLACK
BLUE
DOOR POSITION
SWITCH
[N/C]
REQUEST-TO-EXIT
SWITCH
[N/O]
COMMON
OUTPUT #4
OUTPUT #3
NOT USED
COMMON
SENSE
REQUEST TO EXIT
COMMON
WIRE PIGTAIL
E
1
E
8
E
7
E
6
E
5
E
4
E
3
E
2
C
NO
C
NC
NO
AUXILIARY OUTPUTS
100mA MAX TO COMMON
{
*
*
Grn Wire
To Earth
Ground
2916P
Keypad
Electric Strike
Door Sensor Switch
2 wires for
door sensor
2 wires
for strike
2 wires for
power supply
earth
ground
