Hach DR 5000 User Manual Download Page 31

Page: 31 / 136

Standard Operations

Press

Paper

to select the paper size.

Select between

•

Letter

•

Legal

•

Executive

•

Press

to confirm.

Note:

Press

again to return to the

PC & Printer

menu.

5.2.6.2 Print data

Press

Recall Data

in the Main Menu.

Select the data source, where the data to be printed are stored.

A list is displayed. Data can be filtered. For more information
see

section 5.3.1.2 on page 35

Press the

PC & Printer

icon to send the data (table, curve)

immediately to the printer.

Highlight

Single point

Filtered data

All data

and press

to confirm.

Sending Data...

is displayed until the data have been printed.

5.2.6.3 HACH Data Trans

The optional HACH Data Trans software must be installed on the
PC for the subsequent to process for measurement data.

Press

PC & Printer

in the Instrument Setup.

Select

Press

Setup

to display the PC Setup screen.

For further installation instructions, refer to the HACH Data
Trans user manual.

Summary of Contents for DR 5000








































































































































Search results

Summary of Contents for DR 5000

Reviews:

Brands by name

Popular brands

Hach DR 5000, User Manual

Search results

Summary of Contents for DR 5000

Reviews:

Brands by name

Popular brands