Haag-Streit AT 900 D Instructions For Use Manual Download Page 13

Page: 13 / 24

DEUTSCH

ENGLISH

FRANÇAIS

ITALIANO

ESPAÑOL

NEDERLANDS

PORTUGUÊS

SVENSKA

DEUTSCH

ENGLISH

FRANÇAIS

ITALIANO

ESPAÑOL

NEDERLANDS

PORTUGUÊS

SVENSKA

5.8.3 Position too high/low

Only part of a semicircle in the upper half (10)

Measuring prism not centered on the eye; eye far too high.

Using the control lever, move the slit lamp upwards.

Nearly entire circle above, incomplete circle below (11)

Measuring prism not centered on the eye; eye still too high.

Using the control lever, move the slit lamp upwards.

Two incomplete circles, the larger one on top (12)

Measuring prism not centered on the eye; eye still too high.

Using the control lever, move the slit lamp upwards.

Correct setting! (13)

Two semicircles appear exactly in the middle of the eyepiece.

5.8.4 Incorrect pressure

The outside borders of the fluorescein bands are in contact

with each other (14)

Not enough pressure.

Increase the pressure slightly by rotating the knob on the

tonometer.

Fluorescein bands are superimposed to form a band (15)

Pressure slightly too low.

Increase the pressure slightly more by rotating the knob

on the tonometer.

Bands are no longer in contact (16)

Pressure is too high.

Lower the pressure by rotating the tonometer knob in the

opposite direction.

Correct setting! (17)

The inside borders of the fluorescein bands are contacting each

other.

6. Software / Help menu / Error messages

The software's help section contains instructions and help for performing an exami‑

nation and descriptions of the error messages. The help can be opened via the F1

key or in the [?] ‑ [Help] menu.

WARNING!

The software must be installed by trained personnel in accordance with

separate installation instructions.

6.1 Error messages on the tonometer display

Description

Measures

The measurement is outside the

permitted tolerances.

The position of the sensor arm is

defective.

If one of these errors appears per‑

manently, send the device to the

corresponding service branch.

The minimum operating voltage

has not been achieved; the device

switches off.

Replace the dead batteries.

Battery voltage too high.

Incorrect battery type fitted.

Insert the correct batteries.

01-IFU_AT900D-7220067-04180_eng.indd 13

21.01.2020 11:12:20

Summary of Contents for AT 900 D

























Search results

Summary of Contents for AT 900 D

Reviews:

Related manuals for AT 900 D

Brands by name

Popular brands

Haag-Streit AT 900 D, Instructions For Use Manual

Search results

Summary of Contents for AT 900 D

Reviews:

Related manuals for AT 900 D

Brands by name

Popular brands