H3C S3100-52P Installation Manual Download Page 32 | Manualshive

Page: 32 / 54

background image

Installation Manual
H3C S3100-52P Ethernet Switch

Chapter 4 Starting up the Switch at the Initial Boot

4-7

Press Ctrl-B to enter Boot Menu... 5

To enter the Boot Menu, press <Ctrl+B> within five seconds after the message “Press
Ctrl-B to enter Boot Menu... 5” appears. If not, the system automatically boots and
displays:

Auto-booting...

Decompress Image............................................

............................................................

............................................................

............................................................

.................OK!

Starting at 0x80100000...

Initialize LSJ1LTSE........................OK!

SDRAM fast selftest........................OK!

Flash fast selftest........................OK!

CPLD selftest..............................OK!

Switch chip selftest.......................OK!

PHY selftest...............................OK!

Please check port leds...............FINISHED!

User interface aux0 is available.

Press ENTER to get started.

The appearance of “Press ENTER to get started” indicates that the switch has
completed its automatic boot.

Press <Enter>; the system displays:

<H3C>

You can configure the switch now.

Note:

z

If the specified host software does not exist, the switch will automatically choose an
existing valid host software to boot.

z

A wide range of command views are available for H3C Series Switches. For more
information on configuration commands and command line interfaces, refer to

H3C

S3100-52P Ethernet Switch Operation Manual

and

H3C S3100-52P Ethernet

Switch Command Manual

.

«
...
30
31
32
33
34
...
»

Summary of Contents for S3100-52P























































Reviews:

No comments

Related manuals for S3100-52P

Brand: Tripp Lite Pages: 80

Brand: Vagner Pool Pages: 5

IDS-105FE Series

Brand: Perle Pages: 2

Brand: Xantech Pages: 32

Brand: Kramer Pages: 29

Brand: Niles Pages: 2

Brand: UNICOM Pages: 8

Brand: Avatar Technologies Pages: 9

ePowerSwitch 1GR2

Brand: Neol Pages: 47

LP-2841M Series

Brand: ICP DAS USA Pages: 7

Brand: FOR-A Pages: 2

Brand: Wise Pages: 100

Brand: CYP Pages: 8

Brand: CYP Pages: 8

Brand: LCI Pages: 4

Brand: RITS-N Pages: 2

HIRSCHMANN MACH 4000 Series

Brand: Belden Pages: 56

Brand: Leviton Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands