H3C S3100-52P Installation Manual Download Page 3

Page: 3 / 54

About This Manual

Related Documentation

In addition to this manual, each H3C S3100-52P Ethernet Switch documentation set

includes the following:

Manual

Description

H3C S3100-52P Ethernet Switch
Operation Manual

It is used for assisting the users in
device configuration and typical
applications.

H3C S3100-52P Ethernet Switch
Command Manual

It is used for assisting the users in using
various commands.

Organization

H3C S3100-52P Ethernet Switch Installation Manual

is organized as follows:

Chapter

Contents

1 Product Overview

Introduces the characteristics and technical
specifications of S3100-52P Ethernet Switches.

2 Preparing for Installation

Introduces the installation preparation and
precaution of S3100-52P Ethernet Switches.

3 Installing the Switch

Introduces the procedures to install an
S3100-52P Ethernet Switch, including the setup
of the mainframe, cards, power supply, and
cables.

4 Starting up the Switch at the
Initial Boot

Introduces the booting process of an
S3100-52P Ethernet Switch, including the
power-on booting of the switch and the system
initialization.

5 Loading Boot ROM and Host
Software

Introduces the ways to load BootROM and host
software for an S3100-52P Ethernet Switch.

6 Maintenance and
Troubleshooting

Introduces the problems that might occur during
the installation and the booting of an S3100-52P
Ethernet Switch and the corresponding
solutions.

Appendix Lightning Protection of
the Switch

Introduces lightning protection of an S3100-52P
Ethernet Switch.

Summary of Contents for S3100-52P























































Search results

Summary of Contents for S3100-52P

Reviews:

Related manuals for S3100-52P

Brands by name

Popular brands

H3C S3100-52P, Installation Manual

Search results

Summary of Contents for S3100-52P

Reviews:

Related manuals for S3100-52P

Brands by name

Popular brands