H3C S3100-16T P-EI-W Quick Start Manual Download Page 50

Page: 50 / 60

Quick Start (For Soliton)
H3C S3100 Series Ethernet Switches

Chapter 3 Installation

3-24

3.3 Connecting Optical Fiber

Caution:

After a switch starts, the optical port may emit invisible radial when
there is no optical connector connected to it and the protective cap
is removed from it. Therefore, do not stare into the optical interface.

Be sure to cover the protective cap within 10 seconds if an optical
connector is not in use to keep the optical connector clean.

Be sure to cover the protective cap if an optical port has no optical
connector attached.

Place the protective caps in a safe place when an optical port has
fiber connected to prepare for the cases the fiber is pulled out.

Note:

The following section describes the procedures to connect optical fiber
to an ONU card. The procedures also apply to other subcards.

Step 1: Remove the protective cap from the optical connector of

the fiber.

Step 2: Remove the protective cap from the PON interface of the

ONU card.

Step 3: Plug the optical connector into the PON interface of the

ONU subcard.

Summary of Contents for S3100-16T P-EI-W





























































Search results

Summary of Contents for S3100-16T P-EI-W

Reviews:

Related manuals for S3100-16T P-EI-W

Brands by name

Popular brands

H3C S3100-16T P-EI-W, Quick Start Manual

Search results

Summary of Contents for S3100-16T P-EI-W

Reviews:

Related manuals for S3100-16T P-EI-W

Brands by name

Popular brands