H3C S3100-16T P-EI-W Quick Start Manual Download Page 4

Page: 4 / 60

Chapter

Contents

2 Installation Preparation

Introduces the installation
preparation and precaution of
S3100 Series Ethernet Switches.

3 Installation

Introduces the procedures to install
an S3100 Series Ethernet Switch,
including the setup of the
mainframe, cards and cables.

4 Lightning Protection of the
Switch

Introduces lightning protection of
S3100 Series Ethernet Switches.

Conventions

The manual uses the following conventions:

Symbols

Convention

Description

Warning

Means reader be extremely careful.
Improper operation may cause bodily
injury.

Caution

Means reader be careful. Improper
operation may cause data loss or damage
to equipment.

Note

Means a complementary description.

Environmental Protection

This product has been designed to comply with the requirements

on environmental protection. For the proper storage, use and disposal

of this product, national laws and regulations must be observed.

Summary of Contents for S3100-16T P-EI-W





























































Search results

Summary of Contents for S3100-16T P-EI-W

Reviews:

Related manuals for S3100-16T P-EI-W

Brands by name

Popular brands

H3C S3100-16T P-EI-W, Quick Start Manual

Search results

Summary of Contents for S3100-16T P-EI-W

Reviews:

Related manuals for S3100-16T P-EI-W

Brands by name

Popular brands