Gruppo Ferroli FZ4B, Use And Installation Instructions

Page: 116 / 292

CONTROLLO ZONE FZ4B
116
cod. FZ4B - 06/2011 (Rev. 00)
EN
"TS" - TRANSPARENT PARAMETERS MENU
The zone controller is equipped with 38 transparent parameters also modi fi able from Remote Control (Service Menu):
Com.Rem. Board FZ4B
Boiler Board
(If arr.)
Description of Transparent Parameters
Range Default
01 P01
Zone1 Min. Temperature
20-90°C 20°C
02 P02
Zone1 Max. Temperature
20-90°C 40°C
03 P03
Zone1 calculated setpoint offset
0-40°C 10°C
04 P04
Not implemented
10-90°C 90°C
05 P05
o01 Zone1 External Probe Curve
0-10 0
06 P06
o02 Zone1 External Probe Offset
20-40°C 30°C
07 P07
Zone2 Min. Temperature 20-90°C 20°C
08 P08
Zone2 Max. Temperature
20-90°C 40°C
09 P09
Zone2 calculated set point offset
0-40°C 0°C
10 P10
Not implemented
10-90°C 90°C
11 P11
o03 Zone2 External Probe Curve
0-10 0
12 P12
o04 Zone2 External Probe Offset
20-40°C 30°C
13 P13
Zone3 Min. Temperature
20-90°C 20°C
14 P14
Zone3 Max. Temperature 20-90°C 80°C
15 P15
Zone3 calculated setpoint offset
0-40°C 0°C
16 P16
Not implemented
10-90°C 90°C
17 P17
o05 Zone3 External Probe Curve
0-10 0
18 P18
o06 Zone3 External Probe Offset
20-40°C 30°C
19 P19
Mixing valve on+off time (Only for Mixed Zones)
0-15sec 15
20 P20
Mixing valve Boost (Only for Mixed Zones)
0-120sec 0sec
21 P21
Mixing valve on+off time for °C (Only for Mixed Zones)
00-15°C/sec 1sec/°C
22 P22
Hot water tank hysteresis 0-20°C 4°C
23 P23
Hot water tank Primary setpoint (Excluding “Stand Alone 1” con fi gurations)
70-85°C 80°C
24 P24
Pump start temperature (Excluding “Stand Alone 1” con fi gurations)
0-60°C 0°C
25 P25
Hot water tank priority
0=Off, 1=On 0=Off
26 P26
Hot water tank setpoint (Only without Remote Control)
10-65°C 55°C
27 P27
Post-circulation time
0-20min 10min
28 P28
Zone pumps status with boiler in DHW mode (Only for "Communicating" con fi gurations with DHW)
0=Off, 1=On 0=Off
29 P29
Delay for Zone 0-255sec 30sec
30 P30
Equal settings for each zone
0=Off, 1=On 0=Off
31 P31
Mixing valve Closing time
0-3min 3min
32 P32
Heating hysteresis (Only for “Stand Alone 2” con fi gurations)
0-10°C 5°C
33 P33
Heating standby time (Only for “Stand Alone 2” con fi gurations)
0-10min 2min
34 P34
Pump activation with card in standby
0=Off, 1=On 0=Off
35 P35
Heating delivery probe enabling (Only for “Stand Alone 2” con fi gurations)
0=Off, 1=On 0=Off
36 P36
Operation with boiler in fault status
0=Off, 1=On 0=Off
37 P37
Legionella protection 0=Off, 1-7 0=Off
38 P38
Boiler Summer/Winter mode
0=On, 1=Off 0=On
Press the + and - buttons to scroll the list of parameters in increasing or decreasing order respectively. To modify the value of a parameter, just press the Ok button after
selecting it: press the + and - buttons to modify it; the setting will be automatically saved. Press the Ok button to return to the list of parameters. Press the Ok button for 3
seconds to return to the Service Menu. Press the Ok button for 5 seconds to exit the card Service Menu, or exiting occurs automatically after 15 minutes.
"IN” - INFORMATION MENU
The card can display the following information:
t01
NTC sensor (T1) between 05 and 125 °C
t02
NTC sensor (T2) between 05 and 125 °C
t03
NTC sensor (T3) between 05 and 125 °C
t04
NTC sensor (T4) between -30 and 70°C (Negative values fl ash)
t05
On/Off Thermostat request or Room temperature measured by Remote Control (RT1) ON/OFF or between 05 and 125 °C
t06
On/Off Thermostat request or Room temperature measured by Remote Control (RT2) ON/OFF or between 05 and 125 °C
t07
On/Off Thermostat request or Room temperature measured by Remote Control (RT3) ON/OFF or between 05 and 125 °C
t08
Zone1 Heating set point (Calculation) between 05 and 125 °C
t09
Zone2 Heating set point (Calculation) between 05 and 125 °C
t10
Zone3 Heating set point (Calculation) between 05 and 125 °C
t11
Zone Card Heating set point (Calculation) between 05 and 125 °C
Press the + and - buttons to scroll the list of information in increasing or decreasing order respectively. To display the value of a parameter, press the Ok button after
selecting it: in case of damaged Sensor, the card will display hyphens. Press the Ok button to return to the list of parameters. Press the Ok button for 3 seconds to return
to the Service Menu. Press the Ok button for 5 seconds to exit the card Service Menu, or exiting occurs automatically after 15 minutes.
"HI" - HISTORY MENU
The card can store the last 10 faults: the History datum item H1 represents the most recent fault that occurred, whereas the History datum item H10 represents the least recent.
The codes of the faults saved are also displayed in the corresponding menu of the Remote Control.
Press the + and - buttons to scroll the list of faults. To display the value of a parameter, press the Ok button after selecting it.
Press the Ok button for 3 seconds to return to the Service Menu. Press the Ok button for 5 seconds to exit the card Service Menu, or exiting occurs automatically after 15
minutes.