Grunbeck WINNI-mat VGX Operation Manual Download Page 49

Page: 49 / 51

Water Softener

WINNI-mat

VGX

Order no. 215 188 040-inter Edited by: KONS-pha-rg G:\BA-188040-INTER-VGX.DOC

Maintenance of water softener WINNI-mat

VGX

Check list

Please enter measured values. Confirm checks with OK or enter repair work performed.

Maintenance performed (date)

Measured values

Water pressure [bar]

Flow pressure [bar]

Residential water meter reading [m³]

Raw water hardness (measured)

°dH

°f

mmol/l

Soft water hardness (measured)

°dH

°f

mmol/l

Soft water hardness

0 °dH

0 °f

0 mmol/l

Inspections and checks of controller and control valve

Controller settings checked

Regeneration release checked

Injector and sieve cleaned

Control valve checked for tightness

Function of driving motor checked

Brine tank and brine valve

Brine tank and brine valve cleaned

Function and settings of brine valve
checked

Connections, hose connections, seals

Seals and hose connections checked

Safety fitting (e.g. system separator)
checked for non-return function

Miscellaneous

Remarks

Service

technician

Company

Working time certification (No.)

Signature

Summary of Contents for WINNI-mat VGX




















































Search results

Summary of Contents for WINNI-mat VGX

Reviews:

Related manuals for WINNI-mat VGX

Brands by name

Popular brands

Grunbeck WINNI-mat VGX, Operation Manual

Search results

Summary of Contents for WINNI-mat VGX

Reviews:

Related manuals for WINNI-mat VGX

Brands by name

Popular brands