background image

2

2-Layer Film Install 

Revision date: 04.17.20

READ THIS DOCUMENT BEFORE YOU BEGIN

These instructions include helpful hints and important information needed 

to safely install the roof cladding. Please read these instructions 

before

 you 

begin. If you have any questions during the assembly, contact Customer 

Service at 1-800-245-9881 for assistance.

SAFETY PRECAUTIONS

•  Wear eye protection.
•  Wear head protection.
•  Wear gloves when handling metal tubes.
•  Use a portable GFCI (Ground Fault Circuit Interrupter) when working 

with power tools and cords.

•  Do not climb on greenhouse or framing during or after construction.
•  Do not occupy greenhouse during high winds, tornadoes, or hurricanes.
•  Provide adequate ventilation if structure is enclosed.
•  Do not store hazardous materials in greenhouse.
•  Provide proper ingress and egress to prevent entrapment.

Important Information

Contents

Important Information ..................................................................................... 2

Required Lumber — Customer-Supplied — Ribbon Boards .......................... 4

Recommended — Customer-Supplied —Baseboards ................................... 5

End Panel Installation Details & Foil Tape Install ........................................... 6

Flashing (PGFLSAXXFCW0063) Installation ................................................. 7

Mark Ribbon Board Location .......................................................................... 9

Baseboards and Ribbon Boards..................................................................... 10

U-Channel (102197) — End Rafters .............................................................. 11

Side U-Channel Installation — Roll-Up Sides ................................................ 12

Inspect Frame Before Film Installation ........................................................... 13

2-Layer Film Roof — Layer 1 (IR/AC) ............................................................ 14

Inflation Fan Kit Installation

 ............................................................................ 17

2-Layer Film Roof — Layer 2 ......................................................................... 18

Seal Greenhouse............................................................................................ 19

DOUBLE-LAYER FILM INSTALLATION

Greenhouses equipped with a double-layer film include a layer that is Infra 

Red (IR) Retention film. 

IMPORTANT!

 

During cover installation, install IR film first! Examine 

film and install it according to instructions printed on the film.

WEAR EYE 

PROTECTION 

WHEN 

INSTALLING 

SPRING WIRE!

WARNING: 

To prevent damage to cover and to prevent serious personal injury,  

 

 

DO NOT attempt to install main cover on windy or stormy days.

Summary of Contents for PGFLSAXXFCW0063




















Reviews: