Growatt Shine Pano User Manual Download Page 31 | Manualshive

Page: 31 / 51

background image

28

4. Click on “Back home”, return to the main interface. To go to the configuration
page, click on the “Parameter”.

5. Setting parameter

A. Set the address of the Shine Pano

The address setting includes IP address, subnet mask, default gateway. If the first 3
figures of IP address and default gateway are the same, you could only set the IP
address rather than the subnet mask, default gateway or DNS.

«
...
29
30
31
32
33
...
»

Summary of Contents for Shine Pano




















































Reviews:

No comments

Related manuals for Shine Pano

Brand: Sentek Pages: 58

READy Mini Concentrator

Brand: Kamstrup Pages: 20

Brand: JASTEC Pages: 13

Brand: Hanna Instruments Pages: 2

Brand: Dataq Pages: 28

Brand: GRAPHTEC Pages: 22

Brand: ABB Pages: 190

Brand: ABB Pages: 53

Brand: ABB Pages: 198

Brand: Hanna Instruments Pages: 2

Brand: AEMC instruments Pages: 8

Brand: Tokyo Sokki Kenkyujo Pages: 133

Brand: Relay Pages: 8

Brand: Relay Pages: 20

Hobo MicroRX RX2105

Brand: Onset Pages: 18

Brand: Onset Pages: 22

Brand: NetWave Pages: 191

Brand: LOVATO ELECTRIC Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands