Greenheck PVF Installation And Operation Manual Download

Page: 24 / 32

Indirect Gas-Fired Heat Modules

4:1 Modulating Furnace Will Not Light

In all cases, verify correct terminals as shown on the unit-specific wiring diagram.

Troubleshooting

Ignition controller (IC#)

red LED blinks

7 times or is on

Ignition controller(s) (IC#) failed

Replace faulty ignition controller(s)

High limit switch (HLC#) open?

Discharge temperature was above high limit setting

Let cool then reset high limit.

Yes

Ignition controller (IC#)

red LED

blinks 6 times

Pressure switch (PS2) failure

Repair or replace pressure switch (PS2)

Combustion blower (CM) not functioning

Replace fusing (FU7), combustion blower or relay (CM)

Yes

Ignition controller (IC#)

red LED blinks

1 time, 2 times or 4 times

Improper manifold pressure

Set high and low manifold pressure

(refer to 4:1 Electronic Modulation Start-Up section)

Faulty spark rod or spark gap does not equal 1/8 inch

Replace spark rod or adjust gap to 1/8 inch

Yes

...continued from previous page

Secondary transformer (TR6) defective

Replace secondary transformer (TR6)

Furnace controller (SC1) defective

Replace furnace controller (SC1)

24 VAC between 24 VAC terminals

on mod valve

Yes

10 VDC between terminals

(+) and (-) on mod valve

Everything is working properly,

consult factory.

Summary of Contents for PVF

































Search results

Summary of Contents for PVF

Reviews:

Related manuals for PVF

Brands by name

Popular brands

Greenheck PVF, Installation And Operation Manual

Search results

Summary of Contents for PVF

Reviews:

Related manuals for PVF

Brands by name

Popular brands