GREAT PLAINS 3S-4000 Operator'S Manual Download Page 30 | Manualshive

Page: 30 / 126

background image

2018-06-19

Table of Contents

195-442M

3S-4000, 3S-4000F, 3S-4000HD, 3S-4000HDF

Table of Contents

Operating Instructions

26

Operating Instructions

This section covers general operating procedures. It
assumes that setup items have been completed for both
drill and tractor.

Experience, machine familiarity and the following
information will lead to efficient operation and good
working habits. Always operate farm machinery with
safety in mind.

General Description

On the standard 3S-4000/F/HD/HDF, field operations are
controlled by tractor cab hydraulic levers. When openers
are lowered, mechanical clutches engage, and the
gauge wheels drive the seed meter shafts. Markers, if
installed, are on a separate circuit.

If the Point Row Option is installed, openers are
controlled by section, and are raised and lowered by
solenoid valves operated by the point row controller.

Seed meters operate at a rate proportional to ground
speed, as set by Drive Type and Seed Rate Handles,
based on the Seed Rate charts, and calibration.

Seeding depth and furrow coverage are controlled by drill
down pressure and row unit setup.

Pre-Start Checklist

?

Carefully read “

Important Safety Information

?

Lubricate the drill as indicated under Lubrication,
“

Maintenance and Lubrication

” on page 74.

?

Check the tires for proper inflation according to “

Inflation Chart

” on page 106.

?

Check for worn or damaged parts and repair or replace
before going to the field.

?

Check all bolts, pins and fasteners. Tighten bolts as
specified on “

Torque Values Chart

” on page 107

?

Check hydraulic hoses, fittings, and cylinders for leaks.
Repair or replace before going to the field.

?

Perform all beginning-of-season and daily service items
under “

Maintenance and Lubrication

” on page 74.

High Pressure Fluid Hazard:

Only trained personnel should work on system hydraulics!

Check all hydraulic lines and fittings before applying pressure.

Relieve pressure before disconnecting hydraulic lines. Wear
protective gloves and safety glasses or goggles when working

with hydraulic systems. Fluid escaping from a very small hole

can be almost invisible. Use paper or cardboard, NOT BODY
PARTS, to check for leaks. Escaping fluid under pressure can

have sufficient pressure to penetrate the skin causing serious

injury. If hydraulic fluid is injected into the skin or eyes, seek
immediate medical assistance from a physician familiar with

this type of injury. Within a few hours gangrene can start to

develop. DO NOT DELAY.

«
...
28
29
30
31
32
...
»

Summary of Contents for 3S-4000































































































































Reviews:

No comments

Related manuals for 3S-4000

Brand: Varec Pages: 74

Brand: Halyard Pages: 84

Brand: PAIDI Pages: 48

Brand: Raven Pages: 27

Brand: Raven Pages: 79

Brand: Raven Pages: 88

Brand: Napoleon Pages: 2

Brand: Raytheon Pages: 62

Brand: NAD Pages: 10

Brand: Cannon Pages: 40

Brand: NARGESA Pages: 34

Brand: Daga Pages: 24

Brand: DAF Pages: 68

Brand: JB-Lighting Pages: 32

Brand: W&H Pages: 72

Brand: Safavieh Pages: 2

Brand: Vendlet Pages: 2

Brand: YOKOGAWA Pages: 75

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands