GREAT PLAINS 3S-4000 Operator'S Manual Download Page 92

Page: 92 / 126

2018-06-19

Table of Contents

Index

195-442M

3S-4000, 3S-4000F, 3S-4000HD, 3S-4000HDF

Table of Contents

Index

Maintenance and Lubrication

Marker Maintenance

Marker Transport Carrier

When marker is folded, the second section should be
centered in transport carrier saddle and be parallel with
top of drill box.

Refer to Figure 96

To adjust height of saddle, loosen

x2 inch U-bolts

that hold carrier tube to mounting bracket. Slide carrier
tube up or down as needed.

Marker Shear Bolt

The marker arm is attached to marker body with a shear
bolt

, which is intended to fail if the marker strikes an

obstruction, allowing the marker to swing back around a
second bolt

If the shear bolt breaks, replace it with an equivalent

-14x2 inch Grade 5 bolt (Great Plains part

802-589C). If that size is not available in your local
market, substitute an M10x0.75 Class 8.8 metric bolt and
nut.

If your conditions result in frequent shears, the marker
shear base has storage holes for spare bolts.



Replacing the bolt with a lower grade, or smaller size,
can result in nuisance shears.

Equipment Damage Risk:

Replacing the bolt with a higher grade can result in marker
damage.

Figure 96

Marker Transport Carrier

18961

Figure 97

Marker Shear Bolt

23204

Summary of Contents for 3S-4000































































































































Search results

Summary of Contents for 3S-4000

Reviews:

Related manuals for 3S-4000

Brands by name

Popular brands

GREAT PLAINS 3S-4000, Operator'S Manual

Search results

Summary of Contents for 3S-4000

Reviews:

Related manuals for 3S-4000

Brands by name

Popular brands