GREAT PLAINS 3S-4000 Operator'S Manual Download Page 20 | Manualshive

Page: 20 / 126

background image

2018-06-19

Table of Contents

195-442M

3S-4000, 3S-4000F, 3S-4000HD, 3S-4000HDF

Table of Contents

Introduction

16

Introduction

Great Plains welcomes you to its growing family of new
product owners. Your Three-Section Folding Drill has
been designed with care and built by skilled workers
using quality materials. Proper setup, maintenance, and
safe operating practices will help you get years of
satisfactory use from the machine.

Models Covered

Document Family

Description of Unit

The 3S-4000/F/HD/HDF is a towed seeding implement.
This three section drill has a working width of 40 feet
(12.2 m). The drill has straight arm, double disk heavy
duty openers. The opener disks make a seed bed, and
seed tubes mounted between the disks place seed in the
furrow. Press wheels following the opener disks close the
furrow and gauge opener seeding depth.

The 3S-4000/F/HD/HDF features active hydraulic down
pressure on the opener frames. When used on a tractor
with closed-center hydraulics, constant down pressure
ensures even opener penetration in uneven ground.
Hydraulic down pressure is adjustable at a single point.

The 3S-4000F and 3S-4000HDF allow you to drill seed
and apply fertilizer in the same field pass. Dividers
partition the drill boxes into seed and fertilizer
compartments. The openers apply dry fertilizer to the
seed trench before the furrow is closed. You also can use
both compartments for seed.

3S-4000-4810

48-Row 10in (25.4cm)

3S-4000-6375

63-Row 7.5in (19.1cm)

3S-4000-7806

78-Row 6in (15.2cm)

3S-4000-4810F

Fertilizer, 48-Row 10in (25.4cm)

3S-4000-6375F

Fertilizer, 63-Row 7.5in (19.1cm)

3S-4000-7806F

Fertilizer, 78-Row 6in (15.2cm)

3S-4000HD-4810

48-Row 10in (25.4cm)

3S-4000HD-6375

63-Row 7.5in (19.1cm)

3S-4000HD-7806

78-Row 6in (15.2cm)

3S4000HDF-4810

Fertilizer, 48-Row 10in (25.4cm)

3S4000HDF-6375

Fertilizer, 63-Row 7.5in (19.1cm)

3S4000HDF-7806

Fertilizer, 78-Row 6in (15.2cm)

195-442M

Operator manual (this document)

195-067P

Parts manual (3S-4000HD/HDF)

195-242P

Parts manual (3S-4000/F)

195-325B

Seed & Fertilizer Rate manual

133-322M

Small Seeds Installation manual

Figure 1

3S-4000HD/HDF Drill

18843

«
...
18
19
20
21
22
...
»

Summary of Contents for 3S-4000































































































































Reviews:

No comments

Related manuals for 3S-4000

Brand: Taurus Pages: 28

Brand: Kärcher Pages: 54

Brand: ABB Pages: 85

Brand: XTA Pages: 29

Brand: vc999 Pages: 59

Brand: Qtx Pages: 3

Brand: Saferoad Pages: 24

Brand: NEILPRYDE Pages: 53

Brand: JAC Pages: 103

Brand: 3Disc Pages: 12

Brand: idiag Pages: 10

Brand: Bandit Pages: 136

Versaflo S Series

Brand: 3M Pages: 11

DBI Sala EXOFIT

Brand: 3M Pages: 32

Brand: 3M Pages: 8

Brand: Accurate Bio-Medical Technology Pages: 35

Brand: Fayat Group Pages: 50

Brand: Halyard Pages: 88

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands