GREAT PLAINS 3S-4000 Operator'S Manual Download Page 33 | Manualshive

Page: 33 / 126

background image

3S-4000, 3S-4000F, 3S-4000HD, 3S-4000HDF

Table of Contents

Operating Instructions

29

2018-06-19

Table of Contents

195-442M

Raising Drill (Transport Lift)

Transport Lift is on a dedicated hydraulic circuit. The
center main frame raises and lowers independently of
the opener sub-frames (which are raised and lowered by
the Opener Lift circuit).

The Transport Lift circuit also includes a cylinder for the
Transport Hooks, which lifts and restrains the
outer/forward ends of the wing sections when folded.

Transport Lift is normally used only when the drill is
folded. Opener Lift, and not Transport Lift, is used for
headland turns in field operations.



If the drill is unfolded, gauge wheels do not lift off the
ground during Transport Lift. The wing sections pivot,
and the gauge wheels remain on the ground. As they
do not caster, they can drag sideways if Transport Lift
is used before Fold.

Transport Lift

1.

Fold the drill (unless this lift is for maintenance or
adjustment). See “

” on page 28.

2.

If the Two Outlet conversion kit is installed, a selector
valve near the hitch must be operated to switch
between Transport Lift and Opener Lift. See “

Selector Valve Operation

” on page 46.

3.

Supply oil to the base (extend) ends of the Transport
Lift cylinders.

Refer to Figure 19

4.

Leave the circuit extended until mainframe lift is
complete, the transport hooks

have engaged, the

wing ends are lifted off the ground, and the front box
lift cylinder

is fully extended.

Refer to Figure 20

5.

Swing the locks up and onto the transport lift
cylinders. They are temporarily held in place with
polymer bumpers. They are firmly held in place when
the cylinder is relaxed in step 7.

Figure 18

Locked-Up Transport Lift

26491

Figure 19

Front Box Lift Ready for Lock

26492

1

2

Figure 20

Transport Lift Cylinder Lock

18960

«
...
31
32
33
34
35
...
»

Summary of Contents for 3S-4000































































































































Reviews:

No comments

Related manuals for 3S-4000

Brand: ZOLL Pages: 5

Brand: Accu-Chek Pages: 3

Brand: iBin Pages: 2

Brand: National Instruments Pages: 16

Brand: Jasco Pages: 11

Brand: Keithley Pages: 32

Brand: jcb Pages: 166

Brand: NARGESA Pages: 50

Brand: Landoll Pages: 52

Brand: Gason Pages: 110

Brand: Gainsborough Pages: 2

Brand: Abus Pages: 2

Brand: Abus Pages: 12

Brand: Abu Garcia Pages: 6

Brand: Nektar Pages: 3

Brand: Youkey Pages: 86

Brand: Wacker Neuson Pages: 62

Brand: ParaBody Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands