GREAT PLAINS 3S-4000 Operator'S Manual Download Page 79

Page: 79 / 126

3S-4000, 3S-4000F, 3S-4000HD, 3S-4000HDF

Table of Contents

Index

Maintenance and Lubrication

2018-06-19

Table of Contents

Index

195-442M

In-Line Filters

If the raising or lowering times of the openers slow
noticeably, check the in-line filters and clean if needed.

Refer to Figure 76

Two filters are located on one each of the down-pressure
adjustment valves. If the Point Row option is installed,
another filter is located on the third adjustment valve.

Refer to Figure 77

To disassemble unscrew end cap of filter. Remove
top retaining washer and screen.

Clean filter screen with solvent and compressed air,
or replace if needed.

When reassembling put screen into filter. Place
retaining washer on top of filter and screw on end
cap.

Figure 76

In-Line Filter Locations

22968

Figure 77

In-Line Filter

25187

Summary of Contents for 3S-4000































































































































Search results

Summary of Contents for 3S-4000

Reviews:

Related manuals for 3S-4000

Brands by name

Popular brands

GREAT PLAINS 3S-4000, Operator'S Manual

Search results

Summary of Contents for 3S-4000

Reviews:

Related manuals for 3S-4000

Brands by name

Popular brands