GREAT PLAINS 3S-4000 Operator'S Manual Download Page 110 | Manualshive

Page: 110 / 126

background image

2018-06-19

Table of Contents

195-442M

3S-4000, 3S-4000F, 3S-4000HD, 3S-4000HDF

Table of Contents

Appendix

106

Appendix

Specifications and Capacities

3S-4000-7806

3S-4000-6375

3S-4000-4810

Row Spacing

6 in. (15.2 cm)

7.5 in. (19.1 cm)

10 in. (25.4 cm)

Row Count

78

63

48

Main Seed Box Capacity

129.6 bushels (4567 liters)

Small Seeds Box Capacity

8.5 bushels (300 liters)

Tractor Requirements

180 hp minimum (134 kW)

Weight, standard model

18136 lbs (8226 kg)

17600 lbs (7983 kg)

16500 lbs (7484 kg)

Weight, standard HD model

a

a. See page 31 for additional weight data.

21734 lbs (9858 kg)

20834 lbs (9450 kg)

19934 lbs (9042 kg)

Weight, standard HDF model

23028 lbs (10446 kg)

22966 lbs (10417 kg)

22905 lbs (10389 kg)

Down-Force per Row

130-209 lbs (59-95 kg)

135-240 lbs (61-109 kg)

144-291 lbs (65-132 kg)

Hydraulic Circuits

3 circuits required, load-sensitive or closed-center 15 to 30 gpm at 2300 psi

Optional kits are available for two-circuit, and open center.

Hitch Load

4800 lbs (2177 kg) folded in maximum loaded configuration

Caution:

negative tongue weight when raised and unfolded

Transport Width

15 feet (4.6 meters)

Operating Width

40 feet (12.2 meters)

Swath

475.0 in. (1.207m)

476.5 in. (1.21m)

480.0 in. (1.219m)

Height

7 feet 4 inches (224 cm)

Field Length

34 feet 8 inches (10.6 meters)

Transport Length

34 feet 8 inches (10.6 meters)

Gauge Wheel Tires

11L-15 8 Ply

265/70B16.5 NHS skid steer

Transport Wheel Tires

12.5L-15 20 Ply

395/55B16.5 NHS skid steer

Tire Inflation Chart

Tire Warranty Information

Wheel

Tire Size

Inflation

All tires are warranted by the original manufacturer of the tire. Tire
warranty information is found in the brochures included with your
Operator’s and Parts Manuals or online at the manufacturer’s web sites
listed below. For assistance or information, contact your nearest
Authorized Farm Tire Retailer.
Manufacturer

Web site

Firestone

www.firestoneag.com

Goodyear

www.goodyearag.com

BKT

www.bkt-tires.com

Titan

www.titan-intl.com

Gleason

www.gleasonwheel.com

Transport

12.5L-15 20 Ply

90 psi

621 kPa

395/55B16.5 NHS Skid

Steer

60 psi

(413 kPa)

Gauge

Wheel

36 psi

248 kPa

265/70B16.5 NHS Skid

Steer

60 psi

(413 kPa)

«
...
108
109
110
111
112
...
»

Summary of Contents for 3S-4000































































































































Reviews:

No comments

Related manuals for 3S-4000

Brand: ABB Pages: 86

Brand: ACS Pages: 56

Brand: Datavideo Pages: 50

Brand: Waterous Pages: 90

Brand: Campbell Pages: 14

Brand: Makita Pages: 60

Brand: JB-Lighting Pages: 60

Brand: LAWO Pages: 459

Brand: earline Pages: 13

Brand: Idex Pages: 141

Brand: IDEAL Networks Pages: 8

Brand: IDEAL Networks Pages: 5

Brand: Qu-Bit Electronix Pages: 15

Brand: U-Line Pages: 3

Brand: U-Line Pages: 2

Brand: Orliman Pages: 11

Brand: Taurus Pages: 38

Brand: Phonocar Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands