GRAUPNER piper cherokee 9589 Instruction Manual Download Page 13 | Manualshive

Page: 13 / 25

background image

GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY

Modifications reserved. No liability for printing errors. 06/2010

13

Prepare the baggage straps from the materials supplied, and attach them as shown.

The canopy can now be fixed to the fuselage. Place the canopy accurately over the
cockpit:  it  should  end  flush  with  the  black  film  at  the  front,  and  with  the  red  film  on
both  sides.  Fix  the  canopy  to  the  fuselage  in  this  position  using  strips  of  clear  ad-
hesive tape.

Glue  the  dummy  lighting  units  to  the  top  of  the  fin  and  rudder  using  UHU  ALLES-
KLEBER Kraft, as shown in the photo.

«
...
11
12
13
14
15
...
»

Summary of Contents for piper cherokee 9589


























Reviews:

No comments

Related manuals for piper cherokee 9589

BALANCE BIKE - GRANDE

Brand: COCOVILLAGE Pages: 3

Midwest FreightReady-to-Run Set

Brand: Lionel Pages: 16

100 English-Chinese Words Book

Brand: LeapFrog Pages: 10

Weekend I-16 TYPE 10

Brand: Eduard Pages: 6

Ninjago Masters of Spinjitzu Wyplash 4645006

Brand: LEGO Pages: 2

Brand: PCM Pages: 13

Brand: MTHTrains Pages: 49

Brand: C&C Models Pages: 23

Brand: Harbor Freight Tools Pages: 10

Brand: Vollmer Pages: 12

Brand: Black Horse Model Pages: 30

Brand: Faller Pages: 8

wonder makers GGV82

Brand: Fisher-Price Pages: 32

Brand: Eduard Pages: 2

EP F-20 Tigershark ElectriFLy

Brand: GREAT PLANES Pages: 16

Brand: INTERACTIVE TOY CONCEPTS Pages: 2

Brand: LGB Pages: 32

Brand: Betzold Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands