GRAUPNER Falcon 12 Manual Download Page 32

Page: 32 / 52

32 / 52

S1019_S1034_S1035_33579_33583_FW2_DE_V1.0sh

Display "Swashplate setting"

SWP sensitivity

Swp setting

Direct stick R +115
Direct stick N +115

SWP sensitiv.(50)C10
Swp rate +85
Swp expo +15

SWP setting

Direct stick R +115
Direct stick N +115

Swp sensitiv. 65
Swp rate +85
Swp expo +15

The "SWP sensitivity" option allows you to adjust the sensitivity

either by specifying fixed values or alternatively by assigning a con-

trol channel (C5 ... C16) that controls the value from the transmitter

with a proportional control. To do this, a rotary or slider control is

assigned to one of the control channels 5 ... 16 and the remaining

settings are left at the default values. In the value field of the "SWP

sensitivity" line, the corresponding channel is then merely to be

selected instead of a fixed value. The current control position is dis-

played in the bracket in front, for example "(50) C10", see lower fig-

ure on the left.
Via corresponding settings in the transmitter, a flight-phase-depen-

dent sensitivity control is also possible, for example via the menu

"Control settings" or the option "Gyro" in the Helimix menu.
• The heli oscillates around the rotor shaft :

The sensitivity should then be reduced until vibration-free flies

are possible in all flight situations.

• The helicopter does not hover in a stable manner and it is sus-

ceptible to wind.
The sensitivity should then be increase until vibration-free flies

are possible in all flight situations.

Adjustment range: 1 … 100, Min or C5 … C16

Note

If a control channel is selected in the "SWP sensitivity" line, but no

control is assigned to it on the transmitter side, the value in brack-

ets corresponds to the current neutral position of this control chan-

nel.

Swp rate

Here is set the max. possible yaw rate for roll and pitch.

Adjustment range: +50 … +120

Expo Swp

Ser

vo tr

Ser

vo tr

Ser

vo tr

Control travel

Expo = +100%

Expo = +50%

Expo = –100%

In this line an exponential curve for the control of roll and nick can

be set.
With a setting of "0" a linear control of the swashplate takes place,

with high percentage values a progressive control is achieved,

whereby the helicopter does not react so sensitive around the mid-

dle of the stick.

Adjustment range: 0 … +50

Note

Expo settings should always be made either in the receiver or in the

transmitter, otherwise the two Expo settings overlap.

Summary of Contents for Falcon 12





















































Search results

Summary of Contents for Falcon 12

Reviews:

Related manuals for Falcon 12

Brands by name

Popular brands

GRAUPNER Falcon 12, Manual

Search results

Summary of Contents for Falcon 12

Reviews:

Related manuals for Falcon 12

Brands by name

Popular brands