GRAUPNER Falcon 12 Manual Download Page 19

Page: 19 / 52

19 / 52

S1019_S1034_S1035_33579_33583_FW2_DE_V1.0sh

SUMDI at channel X

SUMD

SUMDI

S1019.AIR GR-18 HoTT (without vario)

---

S1034 Falcon 12 plus

S1035 Falcon 12

33579 GR-18 HoTT (with vario)

---

33583 GR-24 Pro HoTT

C10

Receiver-specific input for a SUMD signal provided by almost all

HoTT receivers.

• "SERVO"

The receiver-specific connection is suitable for operating a servo

or comparable RC components.

• "SUMDI"

- If a receiver set to "SUMD" or “SUMD3” is connected to a

receiver set to "SUMDI" as described under "SUMD on chan-

nel X", a simple satellite connection is created with the

receiver set to SUMDI as the main receiver.

ശ

If two suitable receivers are placed on SUMDI as well as on

SUMD and connected crosswise with two satellite cables, a
reciprocal satellite connection is created.

• “SBUSin” (only Falcon 12 and Falcon 12 plus)

- If a receiver set to “SBUS” or SBUS compatible receiver is con-

nected to a receiver set to “SBUSin” as described under “Kx:

SBUSin”, a simple satellite connection is created with the

receiver set to SBUSin as the main receiver.

ശ

If two suitable receivers are placed on SBUSin as well as on

SBUS and connected crosswise with two satellite cables, a
reciprocal satellite connection is created.

Servo/Sensor/Voltage

S1019.AIR GR-18 HoTT (without

vario)

S1034 Falcon 12 plus

S1035 Falcon 12

33579 GR-18 HoTT (with vario)

33583 GR-24 Pro HoTT

---

• SERVO

The receiver-specific connection is suitable for operating a servo

or comparable RC components.

• SENSOR

Summary of Contents for Falcon 12





















































Search results

Summary of Contents for Falcon 12

Reviews:

Related manuals for Falcon 12

Brands by name

Popular brands

GRAUPNER Falcon 12, Manual

Search results

Summary of Contents for Falcon 12

Reviews:

Related manuals for Falcon 12

Brands by name

Popular brands