GRAUPNER Falcon 12 Manual Download

Page: 29 / 52

29 / 52

S1019_S1034_S1035_33579_33583_FW2_DE_V1.0sh

Rudder

Movement of the model

Control surface action (tail view)

Display "Servo limit"

In this menu, the servo travel for all channels can be limited, so that

the servos in gyro mode cannot run to the mechanical stop.

Servo limit setting step-by-step

1. Bring the angle bracket to the desired line.

Moving down the angle bracket beyond the lower edge of the dis-

play will also display additional channels.

2. Push or tap on the ENT key.

Instead of "SEL" on the right edge of the display, "STO" is dis-

played.

3. Now move the servo to be limited in the desired direction and

position.
The corresponding percentage display is displayed inverted.

4. Push or tap on the ENT key.

The displayed value is saved and "SEL" is displayed again instead

of "STO".

5. Follow the same procedure for further limitations.

SERVO LIMIT

2: -150% +150% SEL
3: -150% +150% SEL

4: -150% +150% SEL

1: -150% +150% SEL

5: -150% +150% SEL

6: -150% +150% SEL
7: -150% +150% SEL

SERVO LIMIT

3: -150% +150% SEL

4: -150% +150% SEL

1: -150% +150% SEL

5: -150% +150% SEL

6: -150% +150% SEL
7: -150% +150% SEL

2: -150%

+083%

STO

SERVO LIMIT

3: -150% +150% SEL

4: -150% +150% SEL

1: -150% +150% SEL

5: -150% +150% SEL

6: -150% +150% SEL
7: -150% +150% SEL

2: -150% +083% SEL

Summary of Contents for Falcon 12





















































Search results

Summary of Contents for Falcon 12

Reviews:

Related manuals for Falcon 12

Brands by name

Popular brands

GRAUPNER Falcon 12, Manual

Search results

Summary of Contents for Falcon 12

Reviews:

Related manuals for Falcon 12

Brands by name

Popular brands