7-008 Setting the Front Height Stops
Illustration 7-008-01, 02
The stop pins „1“ of the front height stops „2“ can be moved in a vertical direction. With unnecessary front
height stops „2“, the stop pins are simply pressed down. They can be pushed up whenever they are needed
without any problem.
After the following are correctly set;
- drawer width according to Section 7-203
- drawer length according to Section 7-206
- back wall height according to Section 7-207,
the front height stops can be set.
Start with the lowest drawer front.
- Slide the unit carrier to the front of the respective drawer width.
- Open both toggle levers „8“.
- Place a front panel „3“ on both front supports „4“.
- Place a drawer bottom „8“ (with the bottom groove towards the machine operator).
- Place a drawer back wall „6“ on the back wall support.
- Insert Zargen slides „7“ , left and right
- Close both toggle levers „8“.
- Lift both Zargen slides „7“ so that the Zargen slide dowel is about 30 mm away from the front „3“.
- Hang up the setting gauge „9“ with the respective page ( 6035 = larger distance of Zargen 6035;
6036 = smaller distance for all other Zargen heights) in the drawer bottom’s dowel hole which is closest
to the front.
- Press the setting gauge „9“ (Notch) against the drawer bottom „5“ (corner).
- Loosen the flap screw „10“ of the front height stop „2“. Slide the front height stop against the drawer front
„3“. Tighten the flap screw „10“.
- Repeat the same on the second side of the Zargen press.
Front height stops can be set in desired quantities, but there must be a minimum distance of about 15 mm.
Smaller distances can lead to problems with the flap screws. In this case, the flap screws can be replaced by
Allen screws M6 X 16. Five front height stops are included in the standard equipment. Additional height
stops can be obtained as accessories.
7-009 Setting the Front Side Stops
Illustration 7-009-01, 02
After the front height stops are set, according to Section 7-208, the front side stops are set.
- Drawer front, bottom, back wall and both Zargen slides are placed in the machine. Close both toggle levers.
- Hang the setting gauge „9“ with the respective side ( 6035 for Zargen 6035, 6036 for all other Zargen
heights ) in the drawer bottom’s dowel hole, which is closest to the front „3“.
- Press the setting gauge „9“ (notch) against the drawer bottom „3“ ( corner ).
- Loosen the flap screw „11“ of the left front side stop „12“. Slide the stops against the drawer front „3“
(between the front and stop, there should be a gap of 0.2 to 0.5 mm). Tighten the flap screw „11“.
- Loosen the flap screw „15“ of the setting collar „13“ on the right spring loaded front side stop. Slide the
setting collar against the guide tube „14“ of the front side stop.
- Tighten the flap screw „15“. ( There should be a gap of 0.5 mm to 1 mm between the setting collar and the
guide tube. The set gap, left and right, serves to balance out the tolerances of the drawer front production).
Front side stops can only be set for a front overhang.
7. OPERATING THE ZPM
The star in your cabinet
29
Summary of Contents for ZPM
