manualshive.com logo in svg

GRASS VALLEY Profile XP PVS1000, Installation Manual

Share
Download
GRASS VALLEY Profile XP PVS1000 Installation Manual Download Page 29

23 February 2004

PVS 2000 Installation Guide

29

Set up PFR700 network settings

This procedure explains how to modify factory default PFR700 network and SNMP 
settings for monitoring with NetCentral Lite or NetCentral Manager. This step is not 
required for PFC500 RAID storage systems.

NOTE: Disregard this step if you are connecting one Profile XP Platform and 
PFC500 RAID storage system to a network using factory default network settings. 
Proceed to “Start NetCentral Lite monitoring software” on page 31.

Refer to the Profile XP Service Manual for information on using NetCentral Lite.

Configuring PFR 700 network and SNMP settings

Network and SNMP settings are set and stored on the LAN card. Therefore the PFR700 
RAID chassis, including its one or two RAID controllers, is a single networked device. 
This is different than other PFR series RAID devices in which each controller is a 
networked device. 

You can use the GVG Disk Utility to configure the following settings for the PFR700 
RAID chassis:

• IP address

• Subnet mask

• Gateway Address

• SNMP trap destinations

To configure these settings, do the following:

1. In the GVG Disk Utility, right-click the icon for a PFR700 controller and select 

Set 

Network Properties

. The Controller Network Settings dialog box opens.

1

5

1

7

Summary of Contents for Profile XP PVS1000















































Reviews:

No comments

Brands by name

Popular brands

Load more brands