Grand Design Momentum Owner'S Manual Download Page 66

Page: 66 / 220

Pre-Travel Information

Recommended Tire Pressure

& Load Limits

The major causes of tire failure are

under-inflated tires

and

overloaded vehicles

Tire information placards and

vehicle certification labels give important information on tires

and load limits,

including

• Recommended Tire Size

• Recommended Tire Inflation Pressure

• Cargo Weight

(

the maximum cargo weight the RV is designed to carry

)

• Front and Rear Gross Axle Weight Ratings (GAWR)

(

the maximum weight the axle system is designed to carry

)

For the label locations and more detailed information,

See

Page 59

Weight Labels

Understanding Tire Pressure

& Load Limits

Load Limits

are determined by the tire size and the greatest

amount of weight each tire can safely carry.

Tire Pressure

is the amount of air pressure a tire requires to

be properly inflated. It is measured in pounds per square inch

(PSI). Tire pressure affects your RV's overall performance and

provides the load-carrying capacity.

The proper tire pressure for your vehicle is referred to as the

cold inflation pressure.

You will also find this number on the

vehicle information placard expressed in both PSI and kilo-

pascals (KPA), the metric measurement used internationally.

It is difficult to obtain the recommended tire pressure when the

tires are not cold.

See the

next page

, Checking Tire Pressure.

Keep tires properly

inflated. A tire that is run

long distances or at high

speeds while seriously

under-inflated will overheat

to the point where the

tire may lose air suddenly

and/or catch fire, possibly

resulting in damage to the

vehicle and its contents

and/or personal injury.

WARNING

Exceeding the established

weight ratings for the

axles, running gear, tires

and wheels can lead to

failure that can affect motor

vehicle safety and lead

to property damage or

damage to the RV.

WARNING

Summary of Contents for Momentum





























































































































































































































Search results

Summary of Contents for Momentum

Reviews:

Related manuals for Momentum

Brands by name

Popular brands

Grand Design Momentum, Owner'S Manual

Search results

Summary of Contents for Momentum

Reviews:

Related manuals for Momentum

Brands by name

Popular brands